- 您現在的位置：買賣IC網 > PDF目錄68773 > 117416-01 (AMETEK Technical and Industrial Products) brushless DC motor blowers controllers PDF資料下載
參數資料
| 型號： | 117416-01 |
| 廠商： | AMETEK Technical and Industrial Products |
| 元件分類： | 馬達/運動控制及驅動器 |
| 英文描述： | brushless DC motor blowers controllers |
| 中文描述： | 直流無刷電機風機控制器 |
| 文件頁數： | 41/57頁 |
| 文件大小： | 2228K |
| 代理商： | 117416-01 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
44
20 Amp BLDC Motor Controller
20MC99
Motor Contoller
Controller Data
48134
Max Continuous Current
20 A
Input Voltage Range
11-52 VDC
Controller PWM Frequency
25 kHz
Analog Speed Input
0-5 VDC
Electrical Hall Spacing
600 or 1200
Waveform
8-Step Trapezoidal
Current Limit Protection
Yes
Rotation
CW / CCW
NOTES:
Temperature: Operating: 0o C to 50°C, Storage Air: -40o C to 85°C
Speed Control: Electrical speed control is achieved by applying a 0 to 5 VDC signal on J4 Pin 12 with respect to J4 Pin 7. Mechanical speed control is achieved by
adjusting the potentiometer when J6 is in position 1 to 2.
Current Control: Trip point is at 20 Amp maximum.
This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The
performance data on this page depicts typical performance under controlled laboratory conditions using constant DC voltages. Actual performance will vary
depending on the operating environment and application. AMETEK Rotron products are not designed for and should not be used in medical life support applications.
AMETEK reserves the right to revise its products without notification.
Caution should be taken. Misplacement of jumper setting will destroy the control.
Jumper Settings:
J5 Set to position 1-2 for 16-52 VDC operation.
Set to position 2-3 for 11-16 VDC operation.
J6 Set to position 1-2 for internal speed adjust.
Set to position 2-3 for analog speed input voltage.
J3 Disable or enable to determine forward/reverse rotation.
J2 Disable for 60° electrical spacing.
Enable for 120° electrical spacing.
J4-6 Brake
J4-12 Analog/In
J1-1 Vin
J4-5 Hall +
J4-11 Freq. Out
J1-2 Phase A
J4-4 Hall 3
J4-10 For./Rev.
J1-3 Phase B
J4-3 Hall 2
J4-9 Output Enable
J1-4 Phase C
J4-2 Hall 1
J4-8 Vref
J1-5 Ground
J4-1 Gnd
J4-7 Ground
相關PDF資料 |
PDF描述 |
|---|---|
| 117417-01 | brushless DC motor blowers controllers |
| 117418-01 | brushless DC motor blowers controllers |
| 117629-02 | 145 MM 240V 400W TF BLOWER |
| 117630-06 | 145 MM 240V 400W TF BLOWER |
| 119000-01 | 64MM MOTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 117416-03 | 制造商:AMETEK Technical and Industrial Products 功能描述:BYPASS BLOWER FOR KODAK PREPRESS PLATESETTER |
| 117-41-620-41-005000 | 制造商:Mill-Max Mfg Corp 功能描述:117-41-620-41-005000 |
| 117-41-620-41-105000 | 制造商:Mill-Max Mfg Corp 功能描述:117-41-620-41-105000 |
| 117-41-628-41-005000 | 制造商:Mill-Max Mfg Corp 功能描述:117-41-628-41-005000 |
| 117-41-628-41-105000 | 制造商:Mill-Max Mfg Corp 功能描述:117-41-628-41-105000 |
發布緊急采購，3分鐘左右您將得到回復。