- 您現在的位置：買賣IC網 > PDF目錄373975 > ADAU1702JSTZ (ANALOG DEVICES INC) SigmaDSP 28-56-Bit Audio Processor with Two ADCs and Four DACs PDF資料下載
參數資料
| 型號： | ADAU1702JSTZ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 消費家電 |
| 英文描述： | SigmaDSP 28-56-Bit Audio Processor with Two ADCs and Four DACs |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| 封裝： | ROHS COMPLIANT, PLASTIC, MS-026BBC, LQFP-48 |
| 文件頁數： | 26/52頁 |
| 文件大?。?/td> | 773K |
| 代理商： | ADAU1702JSTZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
ADAU1702
SELF-BOOT
On power-up, the ADAU1702 can load a program and a set
of parameters that have been saved in an external EEPROM.
Combined with the auxiliary ADC and the multipurpose pins,
this eliminates the need for a microcontroller in the system. The
self-booting is accomplished by the ADAU1702 acting as a master
on the I
2
C bus on start-up, which occurs when the SELFBOOT
pin is set high. The ADAU1702 cannot self-boot in SPI mode.
The maximum necessary EEPROM size for program and
parameters is 6688 bytes, or just over 6.5 kB. This does not
include register settings or overhead bytes, but such factors do
not add a significant number of bytes. This much memory is
only needed if the program RAM (512 × five bytes), parameter
RAM (1024 × four bytes), and interface registers (8 × four
bytes) are completely full. An 8 kB EEPROM has sufficient
memory for this application.
A self-boot operation is triggered on the rising edge of RESET
when the SELFBOOT and WP pins are set high. The ADAU1702
reads the program, parameters, and register settings from the
EEPROM. After the ADAU1702 finishes self-booting, additional
messages can be sent to the ADAU1702 on the I
2
C bus, although
this typically is not necessary in a self-booting application. The
I
2
C device address is 0x68 for a write and 0x69 for a read in this
mode. The ADDRx pins have different functions when the chip
is in this mode, so the settings on them are ignored.
The ADAU1702 does not self-boot if WP is set low. Holding
this pin low allows the EEPROM to be programmed in-circuit.
The WP pin is pulled low (it typically has a resistor pull-up) to
enable writes to the EEPROM, but this in turn disables the self-
boot function until the WP pin is returned high.
The ADAU1702 is a master on the I
2
C bus during self-boot and
writeback. Although it is uncommon for an application using
self-boot to also have a microcontroller connected to the control
lines, care should be taken that no other device tries to write to the
I
2
C bus during self-boot or writeback. The ADAU1702 generates
SCL at 8 × f
S
; therefore, for a f
S
of 48 kHz, SCL runs at 384 kHz.
SCL has a duty cycle of 3/8 in accordance with the I
2
C specification.
The ADAU1702 reads from EEPROM Chip Address 0xA1. The
LSBs of the addresses of some EEPROMs are pin configurable;
in most cases, these pins should be tied low to set this address.
Rev. 0 | Page 26 of 52
EEPROM Format
The EEPROM data contains a sequence of messages. Each
discrete message is one of the seven types defined in Table 19.
Each message consists of a sequence of one or more bytes. The
first byte identifies the message type. Bytes are written MSB
first. Most messages are block write (0x01) types, which are
used for writing to the ADAU1702 program RAM, parameter
RAM, and control registers.
The body of the message following the message type should
start with a 0x00 byte—this is the chip address. As with all
other control port transactions, following the chip address is
a 2-byte register/memory address field.
Table 20 shows an example of what should be stored in the
EEPROM, starting with EEPROM Address 0. In this example,
the interface registers are first set to control port write mode
(Line 1), which is followed by 18 no-operation (no-op) bytes
(Line 2 to Line 4) so that the interface register data appears on
Page 2 of the EEPROM. Next, follows the write header (Line 4)
and then 32 bytes of interface register data (Line 5 to Line 8).
Finally, the program RAM data, starting at ADAU1702 Address
0x04, 0x00 is written (Line 9 to Line 11). In this example, the
program length is 70 words, or 350 bytes, so 332 more bytes
are included in the EEPROM but are not shown in Table 20.
Writeback
A writeback occurs when the WB pin is triggered and data is
written to the EEPROM from the ADAU1702. This function is
typically used to save the volume setting and other parameter
settings to the EEPROM just before power is removed from the
system. A rising edge on the WB pin triggers a writeback when
the device is in self-boot mode, unless a message to set the WB
to the falling edge sensitive (0x05) is contained in the self-boot
message sequence. Only one writeback takes place unless a
message to set multiple writebacks (0x04) is contained in the
self-boot message sequence. The WP pin is pulled low when a
writeback is triggered to allow writing to the EEPROM.
The ADAU1702 is only capable of writing back the contents of
the interface registers to the EEPROM. These registers are usually
set by the DSP program, but can also be written to directly after
setting Bit 6 of the core control register. The parameter settings
that should be saved are configured in SigmaStudio.
相關PDF資料 |
PDF描述 |
|---|---|
| ADAU1702JSTZ-RL | SigmaDSP 28-56-Bit Audio Processor with Two ADCs and Four DACs |
| ADC912A | CMOS Microprocessor-Compatible 12-Bit A/D Converter |
| ADC912AFP | CMOS Microprocessor-Compatible 12-Bit A/D Converter |
| ADC912AFS | CMOS Microprocessor-Compatible 12-Bit A/D Converter |
| ADCMP341 | Dual 0.275% Comparators and Reference with Programmable Hysteresis |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADAU1702JSTZ-RL | 功能描述:IC AUDIO PROC 2ADC/4DAC 48-LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻處理 系列:SigmaDSP® 其它有關文件:STA321 View All Specifications 標準包裝:1 系列:Sound Terminal™ 類型:音頻處理器 應用:數字音頻 安裝類型:表面貼裝 封裝/外殼:64-LQFP 裸露焊盤 供應商設備封裝:64-LQFP EP（10x10） 包裝:Digi-Reel® 其它名稱:497-11050-6 |
| ADAU1761 | 制造商:AD 制造商全稱:Analog Devices 功能描述:SigmaDSP Stereo, Low Power, 96 kHz, 24-Bit Audio Codec with Integrated PLL |
| ADAU1761BCPZ | 功能描述:IC SIGMADSP CODEC PLL 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 編解碼器 系列:SigmaDSP® 標準包裝:2,500 系列:- 類型:PCM 數據接口:PCM 音頻接口 分辨率（位）:15 b ADC / DAC 數量:1 / 1 三角積分調變:是 S/N 比，標準 ADC / DAC (db):- 動態范圍，標準 ADC / DAC (db):- 電壓 - 電源，模擬:2.7 V ~ 3.3 V 電壓 - 電源，數字:2.7 V ~ 3.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-VFBGA 供應商設備封裝:80-BGA MICROSTAR JUNIOR（5x5） 包裝:帶卷 (TR) 其它名稱:296-21257-2 |
| ADAU1761BCPZ | 制造商:Analog Devices 功能描述:IC, AUDIO CODEC, 24BIT, 96KHZ, LFCSP-32 |
| ADAU1761BCPZ-R7 | 功能描述:IC SIGMADSP CODEC PLL 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 編解碼器 系列:SigmaDSP® 標準包裝:2,500 系列:- 類型:立體聲音頻 數據接口:串行 分辨率（位）:18 b ADC / DAC 數量:2 / 2 三角積分調變:是 S/N 比，標準 ADC / DAC (db):81.5 / 88 動態范圍，標準 ADC / DAC (db):82 / 87.5 電壓 - 電源，模擬:2.6 V ~ 3.3 V 電壓 - 電源，數字:1.7 V ~ 3.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-WFQFN 裸露焊盤 供應商設備封裝:48-TQFN-EP（7x7） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。