- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1025A (Analog Devices, Inc.) Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 PDF資料下載
參數資料
| 型號： | ADM1025A |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 圓形連接器 |
| 英文描述： | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
| 中文描述： | 低成本PC硬件監視器的ASIC |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 164K |
| 代理商： | ADM1025A |
REV. A
ADM1025/ADM1025A
–12–
Table IV. Controlling the Operation of
INT
Test Register
Bit 1
Bit 0
Function
0
0
1
1
0
1
0
1
Interrupts Disabled
Thermal Interrupt Only
Voltage Interrupt Only
Voltage and Thermal Interrupts
Note that Bit 7 of VID register should be zero, and that Bits 2 to 7 of Test
Register must be zeros.
When Pin 16 is used as a
RST
or
INT
output, it is open-drain and
requires an external pull-up resistor. This will restrict the address
function on Pin 16 to being high at power-up. If the
RST
or
INT
function is required and
two
ADM1025/ADM1025As are to be
used on the same serial bus, A1/A0 can be set to 10 by using a
high value pull-up on Pin 16 (100 k
or greater). This will not
override the “floating” condition of ADD during power-up.
Note, however, that the
RST
/
INT
outputs of two or more
devices cannot be wire-OR’d, as the devices would then have
the same address. If the
RST
/
INT
outputs need to be connected
to a common interrupt line, they can be OR’d together using the
circuit of Figure 13.
If the
RST
or
INT
functionality is not required, a third address
may be used by setting A1/A0 to 00 by using a 1 k
pull-down
resistor on Pin 16. Note that this address should not be used if
RST
or
INT
is required, since using this address will cause the
device to appear to be generating resets or interrupts, since Pin
16 will be permanently tied low.
A1/A0 = 10
ADD/
RST
/
INT
/NTO
ADM1025/
ADM1025A
#2
SDA
SCL
R2
470k
V
CC
A1/A0 = 01
R1
1k
V
CC
R5
4.7k
V
CC
RST
OR
INT
OPEN-COLLECTOR
AND GATE
ADD/
RST
/
INT
/NTO
ADM1025/
ADM1025A
#1
SDA
SCL
Figure 13. Using Two ADM1025/ADM1025As on the
Same Bus with a Common Interrupt
GENERATING AN
SMBALERT
The
INT
output can be used as an interrupt output or can be
used as an
SMBALERT
. One or more
INT
outputs can be con-
nected to a common
SMBALERT
line connected to the master.
If a device’s
INT
line goes low, the following procedure occurs:
1.
SMBALERT
pulled low.
2. Master initiates a read operation and sends the Alert
Response Address (ARA = 0001 100). This is a general call
address that must not be used as a specific device address.
3. The device whose
INT
output is low responds to the Alert
Response Address, and the master reads its device address.
The address of the device is now known and it can be inter-
rogated in the usual way.
4. If more than one device’s
INT
output is low, the one with
the lowest device address will have priority, in accordance
with normal SMBus arbitration.
5. Once the ADM1025/ADM1025A has responded to the Alert
Response Address, it will reset its
INT
output; however, if
the error condition that caused the interrupt persists,
INT
will be reasserted on the next monitoring cycle.
NAND TREE TESTS
A NAND tree is provided in the ADM1025/ADM1025A for
Automated Test Equipment (ATE) board level connectivity
testing. The device is placed into NAND Test Mode by power-
ing up with Pin 9 (D-/NTI) held high. This pin is automatically
sampled after power-up and if it is connected high, the NAND
test mode is invoked.
In NAND test mode, all digital inputs may be tested as illus-
trated below. ADD/
RST
/
INT
/NTO will become the NAND test
output pin.
To perform a NAND tree test, all pins are initially driven low.
The test vectors set all inputs low, then one-by-one toggle them
high (keeping them high). Exercising the test circuit with this
“walking one” pattern, starting with the input closest to the out-
put of the tree, cycling toward the farthest, causes the output of
the tree to toggle with each input change. Allow for a typical
propagation delay of 500 ns. The structure of the NAND tree is
shown in Figure 14.
ADD/
RST
/
INT
/NTO
SDA
SCL
VID0
VID1
VID2
VID3
Figure 14. NAND Tree
Note: If any of the inputs shown in Figure 14 are unused, they
should not be connected directly to ground, but via a resistor
such as 10 k
. This will allow the ATE (Automatic Test Equip-
ment) to drive every input high so that the NAND tree test can
be properly carried out. Refer to Table XVI for Test Vectors.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1025AARQ | Low-Cost PC Hardware Monitor ASIC |
| ADM1025ARQ | Low-Cost PC Hardware Monitor ASIC |
| ADM1026 | Complete Thermal and System Management Controller |
| ADM1026JST-REEL | Complete Thermal and System Management Controller |
| ADM1026JSTZ-REEL | Complete Thermal and System Management Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1025AARQ | 功能描述:IC MONITOR SYS/VOLT 5CH 16QSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ADM1025AARQ-REEL | 制造商:Rochester Electronics LLC 功能描述:PC HARDWARE MONITOR I.C. - Tape and Reel |
| ADM1025AARQZ | 功能描述:IC MONITOR SYS/VOLT 5CH 16QSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ADM1025ARQ | 功能描述:IC MONITOR SYS/VOLT 5CH 16QSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ADM1025ARQ-REEL | 功能描述:IC MONITOR SYS/VOLT 5CH 16QSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
發布緊急采購，3分鐘左右您將得到回復。