- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1026JST-REEL (ANALOG DEVICES INC) Complete Thermal and System Management Controller PDF資料下載
參數資料
| 型號： | ADM1026JST-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 電源管理 |
| 英文描述： | Complete Thermal and System Management Controller |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026BBC, LQFP-48 |
| 文件頁數： | 11/56頁 |
| 文件大?。?/td> | 634K |
| 代理商： | ADM1026JST-REEL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
ADM1026
Fan Speed Control Outputs
The ADM1026 has two outputs intended to control fan speed,
though they can also be used for other purposes. Pin 18 is an
open drain, pulse width modulated (PWM) output with a
programmable duty cycle and an output frequency of 75 Hz.
Pin 23 is connected to the output of an on-chip, 8-bit, digital-to-
analog converter with an output range of 0 V to 2.5 V.
Rev. A | Page 11 of 56
Either or both of these outputs may be used to implement a
temperature-controlled fan by controlling the speed of a fan
using the temperature measured by the on-chip temperature
sensor or remote temperature sensors.
INTERNAL REGISTERS
Table 4 describes the principal registers of the ADM1026. For
more detailed information, see Table 11 to Table 124.
Table 4. Principal Registers
Type
Address Pointer
Description
Contains the address that selects one of
the other internal registers. When writing
to the ADM1026, the first byte of data is
always a register address, and is written
to the address pointer register.
Provide control and configuration for
various operating parameters.
Contain counter prescaler values for fan
speed measurement.
Contain speed values for PWM and DAC
fan drive outputs.
Configure the GPIO pins as input or
output and for signal polarity.
Store the results of analog voltage inputs,
temperature, and fan speed
measurements, along with their limit
values.
Store events from the various interrupt
sources.
Allow masking of individual interrupt
sources.
Configuration
Registers
Fan Divisor
Registers
DAC/PWM
Control Registers
GPIO Configuration
Registers
Value and Limit
Registers
Status Registers
Mask Registers
EEPROM
The ADM1026 has 8 kB of nonvolatile, electrically erasable,
programmable read-only memory (EEPROM) from register
Addresses 8000h to 9FFFh. This may be used for permanent
storage of data that is not lost when the ADM1026 is powered
down, unlike the data in the volatile registers. Although referred
to as read-only memory, the EEPROM can be written to (as well
as read from) via the serial bus in exactly the same way as the
other registers. The main differences between the EEPROM and
other registers are
An EEPROM location must be blank before it can be
written to. If it contains data, it must first be erased.
Writing to EEPROM is slower than writing to RAM.
Writing to the EEPROM should be restricted because its
typical cycle life is 100,000 write operations, due to the
usual EEPROM wear-out mechanisms.
The EEPROM in the ADM1026 has been qualified for two key
EEPROM memory characteristics: memory cycling endurance
and memory data retention.
Endurance qualifies the ability of the EEPROM to be cycled
through many program, read, and erase cycles. In real terms,
a single endurance cycle is composed of four independent,
sequential events, as follows:
1.
Initial page erase sequence
2.
Read/verify sequence
3.
Program sequence
4.
Second read/verify sequence
In reliability qualification, every byte is cycled from 00h to FFh
until a first fail is recorded, signifying the endurance limit of the
EEPROM memory.
Retention quantifies the ability of the memory to retain its
programmed data over time. The EEPROM in the ADM1026
has been qualified in accordance with the formal JEDEC
Retention Lifetime Specification (A117) at a specific junction
temperature (T
J
= 55°C) to guarantee a minimum of 10 years
retention time. As part of this qualification procedure, the
EEPROM memory is cycled to its specified endurance limit
described above before data retention is characterized. This
means that the EEPROM memory is guaranteed to retain its
data for its full specified retention lifetime every time the
EEPROM is reprogrammed. Note that retention lifetime based
on an activation energy of 0.6 V derates with T
J
, as shown in
Figure 16.
JUNCTION TEMPERATURE (°C)
250
R
300
100
200
150
50
0
50
60
70
80
90
100
40
110
120
0
Figure 16. Typical EEPROM Memory Retention
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1026JSTZ-REEL | Complete Thermal and System Management Controller |
| ADM1026JST | Circular Connector; No. of Contacts:28; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:19-28 |
| ADM1030ARQ | Intelligent Temperature Monitor and PWM Fan Controller |
| ADM1030 | Circular Connector; No. of Contacts:66; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:19-35 |
| ADM1033 | Thermal Monitor and Fan Speed (RPM) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1026JST-REEL7 | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1026JSTZ | 功能描述:PMIC 解決方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| ADM1026JSTZ-R7 | 功能描述:PMIC 解決方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| ADM1026JSTZ-REEL | 功能描述:板上安裝溫度傳感器 HI INT SYS MONITR IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADM1026JSTZ-REEL7 | 制造商:Analog Devices 功能描述:IC SYSTEM MONITOR 制造商:ON Semiconductor 功能描述:IC SYSTEM MONITOR |
發布緊急采購，3分鐘左右您將得到回復。