久久精品国产亚洲精品,又大又肥硕的奶头小说,国农村精品国产自线拍

詳細信息

SPECIFICATION

承認書

DESIGNATION品名：

MODEL型號

EDITION版本：01

PAGE頁碼：1 of 2

1. RATING額定值:

.DC48V0.2A

2. OPERATIONTEMPERATURERANGE使用溫度範圍：

-30～+70℃

3.PRESERVATIVETEMPERATURERANGE保存溫度範圍：

-40～+85℃

4. CONSTRUCTION DIMENSION結構尺寸：

Apply to the appended drawing：
符合附加圖紙

ITEM項目

TEST CONDITION測試條件

SPECIFICATION規格

5. ELECTRONICAL CHARACTERISTICS.電氣性能.

CONTACT RESISTANCE
接觸阻抗

Being measured at 1KHz small current contact resistance meter.
在1KHZ小電流下測量.

30MΩmax
30毫歐以下.

INSULATION
RESISTANCE
絕緣阻抗

Measurements shall be made following application of DC100V potential across terminals and across terminals and frame for 1 minute.
在端子之間和端子與殼之間加DC100V條件下,持續1分鐘測量.

100MΩmin
100兆歐以上.

WITHSTAND
VOLTAGE
耐電壓

AC500V (50Hz or 60Hz) shall be applied across terminals and across terminals and frame for one minute
在端子之間和端子與殼之間加AC500V(50HZ或60HZ)條件下,持續1分鐘測量.

There shall be no breakdown.
無擊穿現象出現.

6. MECHANICAL CHARACTERISTICS.機械性能.

ACTIONPOWER
動作力

Action Power 5-25N
動作力 5-25N

TERMINAL STRENGTH
端子強度

A static force of 500gf being applied in one direction on the tip of terminal for 1 minute.
一個500克之靜負荷施加於端子頂部的一個方向持續1分鐘。

There shall be no sign of damage mechanically and electrically.
無任何跡象顯示機械及電氣性能之損壞.

7. DURABILITY.耐久性.

SOLDERING TEST.
可焊性試驗

The tip of the terminals shall be dipped 2mm in the solder bath at a temperature of 250±5℃for2±0.5sec.端子頂部被浸入焊錫池2mm深,溫度230±5℃時間2±0.5秒。

A new uniform coating of solder shall cover a minimum of90of the surface being immersed.浸入的部分90%以上表面將被錫覆蓋.

RESISTANCE TOSOLDERING HEAT
耐焊接熱

Soldering area:t/2 of P.C.B thickness焊接面積：印刷基板的1/2厚度處
temperature:260±5℃Sinkingtime: 5±1S.焊接溫度：250±5℃，焊接時間：5±1秒。

No damage (electrical and mechanical)
無異常。（電氣、機械特性）

EDITION
版本

DATE
日期

WRTN
制定

CHKD
審核

APVD
批準

DESCRIPTIONS
備註

Lerble

SPECIFICATION
承認書

DESIGNATION品名：

MODEL型號：

EDITION版本：01

PAGE頁碼：2of 2

ITEM項目

TEST CONDITION測試條件

SPECIFICATION規格

LIFE TEST.
壽命試驗

5,000 cycles of operation at a rate of60cycles per minute with unloading.
無負載條件下,每分鐘30次的速度操作5,000次。

(1). Contact resistance .200mΩmax接觸阻抗200毫歐以下.
(2). Insertion and withdraw force±30 initial value插拔力變化範圍初始值±30%
(3). ITEM專案-5B
(4). ITEM專案-5C
(5). ITEM專案-6B

HEAT TEST.
耐熱試驗

85±2℃for96hours after test keep in normal condition for60minutes.
在85±2℃環境中放96小時,再放在正常環境中60分鐘後進行測試。

(1). Contact resistance 50mΩmax.接觸電阻200毫歐以下
(2). Insulation resistance. 50MΩmin.絕緣電阻100兆歐以上
(3). There shall be no sign of damage mechanically and electrically.無任何跡象顯示機械及電器性能之損壞.

HUMIDITY TEST.
耐濕試驗

The condition of temperature60±2℃and humidty 90-95%for96hrs. after test keep in normal condition for60min.
在溫度60±2℃，濕度90-95%環境中放96小時,再放在正常環境中60分鐘後進行測試。

COLD TEST.
耐冷試驗

At –40±2℃for96hrs. after test keep in normal condition for60min.
在-40±2℃環境中放96小時,再置於正常環境中60分鐘後進行測試。

SALTSPRAYTEST
鹽霧試驗

At 5% Nacl liquor for12hours, after washing, keep in normal condition for 30 min.
浸入5%的Nacl溶液中12小時，用水清洗並
在室溫下放置30分鐘

Without excessive Corrosion or crack in appearance
表面無明顯腐蝕或裂紋

8. STANDARD CONDITION試驗、測定狀態

Unless otherwise specified, the test and measurements shall be carried out as follows:
Ambient temperature溫度：5-35℃
Relative humidity相對濕度：45~85%
Air pressure氣壓：86~106kPa(860~1060mbar)
However if doubt arises on the decision based on the measured values under the above-mentioned conditions, the following condition
shall be employed:但在對判定産生疑義時，按下述狀態實施：
Ambient temperature溫度：20±2℃
Relative humidity相對濕度：65±5%
Air pressure氣壓：86~106kPa(860~1060mbar)