詳細信息
產品簡介
A special sonic transducer is used for the ultrasonic proximity sensors, which allows for
alternate transmission and reception of sound waves. The transducer emits a number of
sonic waves which are reflected by an object, back to the transducer. After emission of
the sound waves, the ultrasonic sensor will switch to receive mode. The time elapsed
between emitting and receiving is proportional to the distance of the object from the
sensor.
Digital and analog output
Sensing is only possible within the detection area. The required sensing
range can be adjusted with the sensor\'s potentiometer or by electronic Teach-in
(Teach-in button or remote Teach-in). If an object is detected within the set area, the
output changes its state. The built-in LED indicates this change.
Design and operation
Target detection Sonic waves are best reflected from hard surfaces. Targets may be solids, liquids, granules
or powders. In fact, ultrasonic sensors are used in many applications where objects
are difficult to detect with optical devices.
Standard target
The standard target is defined as a square flat object of following sizes:
• 15 x 15 mm for Sde up to 250 mm
• 30 x 30 mm for Sde up to 1000 mm
• 100 x 100 mm for Sde > 1000 mm
The target should be mounted perpendicular to the axis of the sensor.
Size
To ensure a reliable object detection, the reflected signal must be large enough. The
intensity of the signal depends on the size of the object. Using a standard object, the
full scanning range Sd is available.
Surfaces
Detection of sound absorbent materials will result in a reduction of the maximum sensing
distance.
The maximum sensing distance can be achieved as long as the maximum roughness of
the object does not exceed 0,2 mm.
Typical sound absorbing materials are:
• foam rubber
• cotton / wool / cloth / felt
• very porous materials
The sonic cone profile charts as found in the spec sheets of this catalog represent the
active sensing areas for ultrasonic sensors. The charts demonstrate the short-range sonic
side lobes, which widen the sensor\'s close-range aperture angle. Due to sound absorption
and air diffusion, the lobes decrease at longer ranges.
Size, shape, surface properties and the direction of target detection have very high influence
on the lateral detecting region of an ultrasonic sensor.
Sonic beam profiles are typical for their whole family, eg. the profile for 100 - 1000 mm represents
all types– digital and analog outputs, etc. of sensors with that sensing range.
When determining the shape of typical sonic cone profiles standard square targets made
of steel are used.
• 15 x 15 mm for Sde up to 250 mm
• 30 x 30 mm for Sde up to 1000 mm
• 100 x 100 mm for Sde > 1000 mm
The targets are positioned perpendicularly to the sensor\'s reference axis, approached
sideways at different distances. The sonic cone profile is then plotted by connecting the
measured points with a line.
The cone shape can vary if round or differently shaped objects are detected.
公司介紹
代理圖爾克，保盟，巴魯夫，施克，各類品牌接近開關銷售聯系電話15601952590，QQ1330150156. DyniscoPT4624-35MPA-6/18壓力傳感器
DyniscoPT462E-35MPA-6/18壓力傳感器
DyniscoTPT463E-35MPA-6/18傳感器
DyniscoPT460E-35MPA-6壓力傳感器
DyniscoPT4626-35MPA-6/18壓力變送器
DyniscoTPT4634-35MPA-6/18變送器
2244SA88B21NNDDACAZZ壓力變送器
DyniscoTPT4636-35MPA-6/18變送器
DyniscoPT492-35MPA-15/46壓力傳感器
2242SA00B21CEFFACAZZ壓力傳感器
DyniscoPT420A-35MPA-6壓力傳感器
MDT422F-1/2-3.5C-15/46壓力變送器
DyniscoEPR6-50MPA-6/18壓力傳感器
2242EA00P20DPEEBCEB106變送器
DyniscoPT412-2CB-6/18-B628壓力變送器
TDT432F-1/2-3.5C-15/46壓力變送器
MDA462-1/2-35MPA-15/46壓力傳感器
PT490-35MPA-15壓力傳感器
DyniscoPT4625-35MPA-6/18壓力變送器
DyniscoSPX2243壓力傳感器
DyniscoPT462XL壓力變送器
DyniscoTPT4635-35MPA-6/18變送器
DyniscoPT460XL-35MPA-6壓力傳感器
DyniscoSPX2242壓力變送器
DyniscoSPX2243壓力變送器
DyniscoSPX2244壓力變送器
DyniscoTPT463XL-35MPA-6/18壓力傳感器
DyniscoPT422A-35MPA-6/18壓力傳感器
DyniscoTPT432A-35MPA-6/18壓力傳感器
DyniscoPT410-35MPA-6壓力傳感器
DyniscoPT412-35MPA-6/18壓力傳感器
DyniscoTPT412-35MA-6/18壓力傳感器
DyniscoDyniPak新伙伴快捷套件
DyniscoPT415D-2CB-6-B628壓力變送器
上海深翔自動化控制有限公司http://www.shsxzdh.com/
....