- 您現在的位置：買賣IC網 > PDF目錄374171 > CS8135YTHA5 (ZF Electronics Corporation) Hook-Up Wire; Conductor Size AWG:20; No. Strands x Strand Size:10 x 30; Jacket Color:Dark Blue; Approval Bodies:UL, CSA; Approval Categories:UL AWM Style 1015, CSA Type TEW, JQA-F-, Passes VW-1 Flame Test; Conductor Material:Copper RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | CS8135YTHA5 |
| 廠商： | ZF Electronics Corporation |
| 英文描述： | Hook-Up Wire; Conductor Size AWG:20; No. Strands x Strand Size:10 x 30; Jacket Color:Dark Blue; Approval Bodies:UL, CSA; Approval Categories:UL AWM Style 1015, CSA Type TEW, JQA-F-, Passes VW-1 Flame Test; Conductor Material:Copper RoHS Compliant: Yes |
| 中文描述： | 5V的，5V低壓降穩壓器與雙/使能復位 |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 180K |
| 代理商： | CS8135YTHA5 |
6
C
Application Notes
The output or compensation capacitor helps determine
three main characteristics of a linear regulator: start-up
delay, load transient response and loop stability.
The capacitor value and type should be based on cost,
availability, size and temperature constraints. A tantalum
or aluminum electrolytic capacitor is best, since a film or
ceramic capacitor with almost zero ESR, can cause insta-
bility. The aluminum electrolytic capacitor is the least
expensive solution, but, if the circuit operates at low tem-
peratures (-25C to -40C), both the value and ESR of the
capacitor will vary considerably. The capacitor manufac-
turers data sheet usually provides this information.
The value for output capacitor C
2
shown in the test and
applications circuit should work for most applications,
however it is not necessarily the optimized solution.
To determine acceptable values for C
2
and C
3
for a partic-
ular application, start with a tantalum capacitor of the rec-
Stability Considerations
S1
ON/OFF
RESET
FLAG
R
1
20k
W
C1*
0.1
m
F
RESET/
ENABLE
V
IN
V
OUT1
Gnd
V
OUT2
C3**
10
m
F
+
+
10
m
F
C2 **
CS8135
NOTES:
* C1 required if regulator is located far from power supply filter.
** C2, C3 required for stability.
Test & Application Circuit
Disabling V
OUT2
when it is not needed. C3 is no longer needed.
Unlike the standby regulated output, which must remain
on whenever possible, the high current regulated output is
fault protected against overvoltage and also incorporates
thermal shutdown. If the input voltage rises above approx-
imately 30V (e.g., load dump), this output will automatical-
ly shutdown. This protects the internal circuitry and
enables the IC to survive higher voltage transients than
would otherwise be expected. Thermal shutdown is effec-
tive against die overheating since the high current output
is the dominant source of power dissipation in the IC.
The
if desired. When controlled in the manner shown in the
test circuit (common in automotive systems where
/ENABLE is connected to the ignition switch), the
lead also serves as an output flag that is active low when-
ever a fault condition is detected with the high current
regulated output. Under normal operating conditions, the
function has the ability to serve a dual purpose
output voltage of this lead is high (5V). This is set by an
internal clamp. If the high current output becomes unreg-
ulated for any reason (line transients, short circuit, thermal
shutdown, low input voltage, etc.) the lead switches to the
active low state, and is capable of sinking several mil-
liamps. This output signal can be used to initiate any reset
or start-up procedure that may be required of the system.
The
lead can also be driven directly from logic cir-
cuits. The only requirement is that the 20k pull-up resis-
tor remain in place. This will not affect the logic gate since
the voltage on this lead is limited by the internal clamp to
5V. The
signal is sacrificed in this arrangement
since the maximum sink capability of the lead in the active
low state (approximately 5mA), is usually not sufficient to
pull down the active high logic gate. The flag can be
retained if the driving gate is open collector logic.
Controlling ON/OFF Terminal with a typical CMOS or TTL Logic Gate
Reset Pulse on Power-Up (with approximately 300ms delay)
RESET/
ENABLE
Gnd
CS8135
R1
20k
W
R2
100k
W
4.7
m
F
CMOS MM 74CO4
or Equivalent
Delayed
Reset
Out
CS8135
V
IN
R1
20k
W
RESET/
ENABLE
RESET
RESET
RESET
RESET
RESET Function
High Current Output
V
IN
V
OUT
2
R
D
10k
W
C
3
+
V
OUT
2
Circuit Description: continued
相關PDF資料 |
PDF描述 |
|---|---|
| CS8135YT5 | 5V, 5V Low Dropout Dual Regulator with /ENABLE RESET |
| CS8141 | 5V, 500mA Linear Regulator with ENABLE, , and Watchdog RESET |
| CS8140YDW24 | T1/E1 Transformer |
| CS8140YDWR24 | T1/E1 Transformer w/Surge Protect |
| CS8140 | 5V, 500mA Linear Regulator with ENABLE, , and Watchdog RESET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS8135YTVA5 | 制造商:CHERRY 制造商全稱:CHERRY 功能描述:5V, 5V Low Dropout Dual Regulator with /ENABLE RESET |
| CS813A1 | 制造商:HVPSI 制造商全稱:High Voltage Power Solutions, Inc. 功能描述:MOV Modules |
| CS813A2 | 制造商:HVPSI 制造商全稱:High Voltage Power Solutions, Inc. 功能描述:MOV Modules |
| CS813B1 | 制造商:HVPSI 制造商全稱:High Voltage Power Solutions, Inc. 功能描述:MOV Modules |
| CS813B2 | 制造商:HVPSI 制造商全稱:High Voltage Power Solutions, Inc. 功能描述:MOV Modules |
發布緊急采購，3分鐘左右您將得到回復。