- 您現在的位置：買賣IC網 > PDF目錄374171 > CS8151YNF16 (ZF Electronics Corporation) Connector assemblies, Network cables; PDF資料下載
參數資料
| 型號： | CS8151YNF16 |
| 廠商： | ZF Electronics Corporation |
| 英文描述： | Connector assemblies, Network cables; |
| 中文描述： | 5V的，100mA的低壓差線性穩壓器，帶有看門狗，復位， |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 196K |
| 代理商： | CS8151YNF16 |
5
To reduce the drain on the battery a system can go into a
low current consumption mode when ever its not per-
forming a main routine. The WAKE UP signal is generated
continuously and is used to interrupt a microcontroller
that is in sleep mode. The nominal output is a 5 volt
square wave with a duty cycle of 50% at a frequency that
is determined by a timing capacitor, C
Delay
.
When the microprocessor receives a rising edge from the
WAKE UP output, it must issue a watchdog pulse and
check its inputs to decide if it should resume normal oper-
ations or remain in the sleep mode.
The first falling edge of the watchdog signal causes the
WAKE UP to go low within 2μs (typ) and remain low until
the next WAKE UP cycle (see Figure 2). Other watchdog
pulses received within the same cycle are ignored (Figure
1).
During power up,
is held low until the output volt-
age is in regulation. During operation, if the output volt-
age shifts below the regulation limits, the RESET toggles
low and remains low until proper output voltage regula-
tion is restored. After the
high.
The WATCHDOG circuitry continuously monitors the
input watchdog signal (WDI) from the microprocessor.
The absence of a falling edge on the WATCHDOG input
during one WAKE UP cycle will cause a
occur at the end of the WAKE UP cycle. (see Figure 1b).
The WAKE UP output is pulled low during a
regardless of the cause of the
returns high, the WAKE UP cycle begins again (see
Figures 1b).
The
pulse width, WAKE UP signal frequency and
high to WAKE UP delay time are all set by one
external capacitor C
Delay
.
WAKE UP period=(4x10
5
)C
Delay
Delay Time=(5x10
4
)C
Delay
HIGH to WAKE UP Delay Time =(2x10
5
)C
Delay
RESET
delay,
returns
pulse to
. After the
Capacitor temperature coefficient and tolerance as well as the
tolerance of the CS8151 must be taken into account in order
to get the correct system tolerance for each parameter.
Figure 2. WAKE UP response to WDI
Figure 3. WAKE UP response to
(Low Voltage)
RESET
WAKE UP
R______
RESET
______
RESET
WAKE UP
WAKE UP
Response to
WDI
WAKE UP
WDI
RESET
RESET
RESET
RESET
RESET
RESET
RESET
RESET
RESET
RESET
Dropout Voltage:
The input-output voltage differential at which the cir-
cuit ceases to regulate against further reduction in
input voltage. Measured when the output voltage has
dropped 100mV from the nominal value obtained at
14V input, dropout voltage is dependent upon load
current and junction temperature.
Input Voltage:
The DC voltage applied to the input terminals with
respect to ground.
Line Regulation:
The change in output voltage for a change in the
input voltage. The measurement is made under con-
ditions of low dissipation or by using pulse tech-
niques such that the average chip temperature is not
significantly affected.
Load Regulation:
The change in output voltage for a change in load
current at constant chip temperature.
Quiescent Current:
The part of the positive input current that does not
contribute to the positive load current. The regulator
ground lead current.
Ripple Rejection:
The ratio of the peak-to-peak input ripple voltage to
the peak-to-peak output ripple voltage.
Current Limit:
Peak current that can be delivered to the output.
Definition of Terms
Circuit Description
C
Functional Description
相關PDF資料 |
PDF描述 |
|---|---|
| CS8151YDPS7 | 5V, 100mA Low Dropout Linear Regulator with WATCHDOG, RESET, & WAKE UP |
| CS8151YDPSR7 | 5V, 100mA Low Dropout Linear Regulator with WATCHDOG, RESET, & WAKE UP |
| CS8151 | 5V, 100mA Low Dropout Linear Regulator with WATCHDOG, RESET, & WAKE UP |
| CS8151YTVA7 | Paired Cable; Number of Conductors:4; Conductor Size AWG:22; No. Strands x Strand Size:7 x 30; Jacket Material:Polyvinylchloride (PVC); Number of Pairs:2; Leaded Process Compatible:Yes; Features:Unshielded; Outer Diameter:0.230" RoHS Compliant: Yes |
| CS8151YDWF16 | 5V, 100mA Low Dropout Linear Regulator with WATCHDOG, RESET, & WAKE UP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS8151YNF16G | 功能描述:低壓差穩壓器 - LDO 5V 100mA w/WatchDog RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| CS8151YT7 | 功能描述:低壓差穩壓器 - LDO 5V 100mA w/WatchDog RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| CS8151YT7G | 功能描述:低壓差穩壓器 - LDO 5V 100mA w/WatchDog RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| CS8151YTHA7 | 功能描述:低壓差穩壓器 - LDO 5V 100mA w/WatchDog RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| CS8151YTHA7G | 功能描述:低壓差穩壓器 - LDO 5V 100mA w/WatchDog RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。