- 您現在的位置：買賣IC網 > PDF目錄379079 > CY7C1484V25-200AXC (CYPRESS SEMICONDUCTOR CORP) 72-Mbit (2M x 36/4M x 18) Pipelined DCD Sync SRAM PDF資料下載
參數資料
| 型號： | CY7C1484V25-200AXC |
| 廠商： | CYPRESS SEMICONDUCTOR CORP |
| 元件分類： | DRAM |
| 英文描述： | 72-Mbit (2M x 36/4M x 18) Pipelined DCD Sync SRAM |
| 中文描述： | 2M X 36 CACHE SRAM, 3 ns, PQFP100 |
| 封裝： | 14 X 20 MM, 1.40 MM HEIGHT, LEAD FREE, PLASTIC, MS-026, TQFP-100 |
| 文件頁數： | 10/26頁 |
| 文件大?。?/td> | 906K |
| 代理商： | CY7C1484V25-200AXC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
CY7C1484V25
CY7C1485V25
Document #: 38-05286 Rev. *H
Page 10 of 26
IEEE 1149.1 Serial Boundary Scan (JTAG)
The CY7C1484V25/CY7C1485V25 incorporates a serial
boundary scan test access port (TAP). This port operates in
accordance with IEEE Standard 1149.1-1990 but does not
have the set of functions required for full 1149.1 compliance.
These functions from the IEEE specification are excluded
because their inclusion places an added delay in the critical
speed path of the SRAM. Note that the TAP controller
functions in a manner that does not conflict with the operation
of other devices using 1149.1 fully compliant TAPs. The TAP
operates using JEDEC-standard 2.5V or 1.8V I/O logic levels.
The CY7C1484V25/CY7C1485V25 contains a TAP controller,
instruction register, boundary scan register, bypass register,
and ID register.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, tie TCK LOW (V
SS
) to
prevent device clocking. TDI and TMS are internally pulled up
and may be unconnected. They may alternatively be
connected to V
DD
through a pull up resistor. TDO must be left
unconnected. During power up, the device comes up in a reset
state, which does not interfere with the operation of the device.
The 0/1 next to each state represents the value of TMS at the
rising edge of TCK.
Test Access Port (TAP)
Test Clock (TCK)
The test clock is used only with the TAP controller. All inputs
are captured on the rising edge of TCK. All outputs are driven
from the falling edge of TCK.
Test Mode Select (TMS)
The TMS input gives commands to the TAP controller and is
sampled on the rising edge of TCK. It is allowable to leave this
ball unconnected if the TAP is not used. The ball is pulled up
internally, resulting in a logic HIGH level.
Test Data-In (TDI)
The TDI ball serially inputs information into the registers and
can be connected to the input of any of the registers. The
register between TDI and TDO is chosen by the instruction
that is loaded into the TAP instruction register. For information
about loading the instruction register, see the
TAP Controller
State Diagram
. TDI is internally pulled up and can be uncon-
nected if the TAP is unused in an application. TDI is connected
to the most significant bit (MSB) of any register. (See
TAP
Controller Block Diagram
.)
Test Data-Out (TDO)
The TDO output ball serially clocks data-out from the registers.
Whether the output is active depends on the current state of
the TAP state machine. The output changes on the falling edge
of TCK. TDO is connected to the least significant bit (LSB) of
any register. (See
TAP Controller State Diagram
.)
Performing a TAP Reset
A RESET is performed by forcing TMS HIGH (V
DD
) for five
rising edges of TCK. This RESET does not affect the operation
of the SRAM and may be performed while the SRAM is
operating.
At power up, the TAP is reset internally to ensure that TDO
comes up in a High-Z state.
TAP Registers
Registers are connected between the TDI and TDO balls and
enable data to be scanned into and out of the SRAM test
circuitry. Only one register can be selected at a time through
the instruction register. Data is serially loaded into the TDI ball
on the rising edge of TCK. Data is output on the TDO ball on
the falling edge of TCK.
TAP Controller State Diagram
TEST-LOGIC
RESET
RUN-TEST/
IDLE
SELECT
DR-SCAN
SELECT
IR-SCAN
CAPTURE-DR
SHIFT-DR
CAPTURE-IR
SHIFT-IR
EXIT1-DR
PAUSE-DR
EXIT1-IR
PAUSE-IR
EXIT2-DR
UPDATE-DR
EXIT2-IR
UPDATE-IR
1
1
1
0
1
1
0
0
1
1
1
0
0
0
0
0
0
0
0
0
1
0
1
1
0
1
0
1
1
1
1
0
TAP Controller Block Diagram
Bypass Register
0
Instruction Register
0
1
2
Identification Register
0
1
2
29
30
31
.
.
.
Boundary Scan Register
0
1
2
.
.
x
.
.
.
Selection
Circuitry
TCK
TMS
TAP CONTROLLER
TDI
TDO
Selection
Circuitry
[+] Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| CY7C1484V25-200AXI | 72-Mbit (2M x 36/4M x 18) Pipelined DCD Sync SRAM |
| CY7C1484V25-200BZC | 72-Mbit (2M x 36/4M x 18) Pipelined DCD Sync SRAM |
| CY7C1485V25-250BZXC | 72-Mbit (2M x 36/4M x 18) Pipelined DCD Sync SRAM |
| CY7C1485V25-250BZXI | 72-Mbit (2M x 36/4M x 18) Pipelined DCD Sync SRAM |
| CY7C1484V33-167AXC | 72-Mbit (2M x 36/4M x 18) Pipelined DCD Sync SRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY7C149 WAF | 制造商:Cypress Semiconductor 功能描述: |
| CY7C149-45PC | 功能描述:1KX4 18-PIN SRAM RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1,000 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:4K (512 x 8) 速度:400kHz 接口:I²C，2 線串口 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.173"，4.40mm 寬） 供應商設備封裝:8-MFP 包裝:帶卷 (TR) |
| CY7C150-10DC | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CY7C150-15PC | 制造商:Rochester Electronics LLC 功能描述:4K (1K X 4)- 24 PIN 300 MIL SEPARATE I/O & RESET SRAM - Bulk |
| CY7C15025PC | 制造商:CYPRESS 功能描述:* |
發布緊急采購，3分鐘左右您將得到回復。