- 您現在的位置：買賣IC網 > PDF目錄379096 > CY7C63723-PC (CYPRESS SEMICONDUCTOR CORP) enCoRe USB Combination Low-Speed USB & PS/2 Peripheral Controller PDF資料下載
參數資料
| 型號： | CY7C63723-PC |
| 廠商： | CYPRESS SEMICONDUCTOR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | enCoRe USB Combination Low-Speed USB & PS/2 Peripheral Controller |
| 中文描述： | 8-BIT, OTPROM, 12 MHz, RISC MICROCONTROLLER, PDIP18 |
| 封裝： | 0.300 INCH, PLASTIC, DIP-18 |
| 文件頁數： | 23/58頁 |
| 文件大?。?/td> | 1236K |
| 代理商： | CY7C63723-PC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
FOR
FOR
enCoRe
USB CY7C63722/23
CY7C63743
Document #: 38-08022 Rev. **
Page 23 of 58
Bit 7: PS/2 Pull-up Enable
This bit is used to enable the internal PS/2 pull-up resistors on the SDATA and SCLK pins. Normally the output high level on
these pins is V
CC
, but note that the output will be clamped to approximately 1 Volt above V
REG
if the VREG Enable bit is set,
or if the Device Address is enabled (bit 7 of the USB Device Address Register,
Figure 14-1
).
1 = Enable PS/2 Pull-up resistors. The SDATA and SCLK pins are pulled up internally to V
CC
with two resistors of approximately
5 k
(see Section 25.0 for the value of R
PS2
).
0 = Disable PS/2 Pull-up resistors.
Bit 6: V
REG
Enable
A 3.3V voltage regulator is integrated on chip to provide a voltage source for a 1.5-k
pull-up resistor connected to the D– pin
as required by the USB Specification. Note that the VREG output has an internal series resistance of approximately 200
, the
external pull-up resistor required is approximately 1.3-k
(see
Figure 16-1
).
1 = Enable the 3.3V output voltage on the VREG pin.
0 = Disable. The VREG pin can be configured as an input.
Bit 5: USB-PS/2 Interrupt Select
This bit allows the user to select whether an USB bus reset interrupt or a PS/2 activity interrupt will be generated when the
interrupt conditions are detected.
1 = PS/2 interrupt mode. A PS/2 activity interrupt will occur if the SDATA pin is continuously LOW for 128 to 256
μ
s.
0 = USB interrupt mode (default state). In this mode, a USB bus reset interrupt will occur if the single ended zero (SE0, D–
and D+ are LOW) exists for 128 to 256
μ
s.
See Section 21.3 for more details.
Bit 4:
Reserved. Must be written as a ‘0’.
Bit 3: USB Bus Activity
The Bus Activity bit is a “sticky” bit that detects any non-idle USB event has occurred on the USB bus. Once set to HIGH by
the SIE to indicate the bus activity, this bit retains its logical HIGH value until firmware clears it. Writing a ‘0’ to this bit clears
it; writing a ‘1’ preserves its value. The user firmware should check and clear this bit periodically to detect any loss of bus
activity. Firmware can clear the Bus Activity bit, but only the SIE can set it. The 1.024-ms timer interrupt service routine is
normally used to check and clear the Bus Activity bit.
1 = There has been bus activity since the last time this bit was cleared. This bit is set by the SIE.
0 = No bus activity since last time this bit was cleared (by firmware).
Bit [2:0]: D+/D– Forcing Bit [2:0]
Forcing bits allow firmware to directly drive the D+ and D– pins, as shown in
Table 13-1
. Outputs are driven with controlled
edge rates in these modes for low EMI. For forcing the D+ and D– pins in USB mode, D+/D– Forcing Bit 2 should be 0. Setting
D+/D– Forcing Bit 2 to ‘1’ puts both pins in an open-drain mode, preferred for applications such as PS/2 or LED driving.
Bit #
7
6
5
4
3
2
1
0
Bit Name
PS/2 Pull-up
Enable
VREG
Enable
USB Reset-
PS/2 Activity
Interrupt
Mode
Reserved
USB
Bus Activity
D+/D– Forcing Bit
Read/Write
R/W
R/W
R/W
-
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
Figure 13-1. USB Status and Control Register (Address 0x1F)
相關PDF資料 |
PDF描述 |
|---|---|
| CY7C63743 | enCoRe USB Combination Low-Speed USB & PS/2 Peripheral Controller |
| CY7C63743-PC | enCoRe USB Combination Low-Speed USB & PS/2 Peripheral Controller |
| CY7C63743C | enCoRe USB Combination Low-Speed USB and PS/2 Peripheral Controller(enCoRe USB結合低速USB和PS/2外設控制器) |
| CY7C63723C | enCoRe USB Combination Low-Speed USB and PS/2 Peripheral Controller(enCoRe USB結合低速USB和PS/2外設控制器) |
| CY7C63803 | enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY7C63723-PXC | 功能描述:IC MCU 8K USB/PS2 LS 18DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382 |
| CY7C63723-SC | 功能描述:IC MCU 8K LS USB/PS-2 18-SOIC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382 |
| CY7C63723-SCT | 制造商:Cypress Semiconductor 功能描述:I/O Controller USB and PS/2 Controller 0.02A 18-Pin SOIC T/R |
| CY7C63723-SXC | 功能描述:IC MCU 8K LS USB/PS-2 18-SOIC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382 |
| CY7C63723-SXCT | 制造商:Cypress Semiconductor 功能描述:I/O Controller USB and PS/2 Controller 0.02A 18-Pin SOIC T/R |
發布緊急采購，3分鐘左右您將得到回復。