參數資料
型號： CY7C63723-PC
廠商： CYPRESS SEMICONDUCTOR CORP
元件分類： 微控制器/微處理器
英文描述： enCoRe USB Combination Low-Speed USB & PS/2 Peripheral Controller
中文描述： 8-BIT, OTPROM, 12 MHz, RISC MICROCONTROLLER, PDIP18
封裝： 0.300 INCH, PLASTIC, DIP-18
文件頁數： 38/58頁
文件大?。?/td> 1236K
代理商： CY7C63723-PC
FOR
FOR
enCoRe
USB CY7C63722/23
CY7C63743
Document #: 38-08022 Rev. **
Page 38 of 58
Bit 7: Wake-up Interrupt Enable
The internal wake-up timer is normally used to wake the part from suspend mode, but it can also provide an interrupt when
the part is awake. The wake-up timer is cleared whenever the Wake-up Interrupt Enable bit is written to a 0, and runs whenever
that bit is written to a 1. When the interrupt is enabled, the wake-up timer provides periodic interrupts at multiples of period,
as described in Section 11.2.
1 = Enable wake-up timer for periodic wake-up.
0 = Disable and power-off wake-up timer.
Bit 6: GPIO Interrupt Enable
Each GPIO pin can serve as an interrupt input. During a reset, GPIO interrupts are disabled by clearing all GPIO interrupt
enable registers. Writing a ‘1’ to a GPIO Interrupt Enable bit enables GPIO interrupts from the corresponding input pin. These
registers are shown in
Figure 21-4
for Port 0 and
Figure 21-5
for Port 1. In addition to enabling the desired individual pins for
interrupt, the main GPIO interrupt must be enabled, as explained in Section 21.0.
The polarity that triggers an interrupt is controlled independently for each GPIO pin by the GPIO Interrupt Polarity Registers.
Setting a Polarity bit to ‘0’ allows an interrupt on a falling GPIO edge, while setting a Polarity bit to ‘1’ allows an interrupt on a
rising GPIO edge. The Polarity Registers reset to 0 and are shown in
Figure 21-6
for Port 0 and
Figure 21-7
for Port 1.
All of the GPIO pins share a single interrupt vector, which means the firmware will need to read the GPIO ports with enabled
interrupts to determine which pin or pins caused an interrupt.The GPIO interrupt structure is illustrated in
Figure 21-8
.
Note that if one port pin triggered an interrupt, no other port pins can cause a GPIO interrupt until that port pin has returned
to its inactive (non-trigger) state or its corresponding port interrupt enable bit is cleared. The CY7C637xx does not assign
interrupt priority to different port pins and the Port Interrupt Enable Registers are not affected by the interrupt acknowledge
process.
1 = Enable
0 = Disable
Bit [5:4]: Capture Timer A and B Interrupts
There are two capture timer interrupts, one for each associated pin. Each of these interrupts occurs on an enabled edge of the
selected GPIO pin(s). For each pin, rising and/or falling edge capture interrupts can be in selected. Refer to Section 19.0. These
interrupts are independent of the GPIO interrupt, described in the next section.
1 = Enable
0 = Disable
Bit 3: SPI Interrupt Enable
The SPI interrupt occurs at the end of each SPI byte transaction, at the final clock edge, as shown in
Figure 17-4
. After the
interrupt, the received data byte can be read from the SPI Data Register, and the TCMP control bit will be high
1 = Enable
0 = Disable
Bit 2: 1.024-ms Interrupt Enable
The 1.024-ms interrupts are periodic timer interrupts from the free-running timer (based on the 6-MHz clock). The user should
disable this interrupt before going into the suspend mode to avoid possible conflicts between servicing the timer interrupts
(128-
μ
s interrupt and 1.024-ms interrupt) first or the suspend request first when waking up.
1 = Enable. Periodic interrupts will be generated approximately every 1.024 ms.
0 = Disable.
Bit #
7
6
5
4
3
2
1
0
Bit Name
Wake-up
Interrupt
Enable
GPIO
Interrupt
Enable
Capture
Timer B
Intr. Enable
Capture
Timer A
Intr. Enable
SPI
Interrupt
Enable
1.024-ms
Interrupt
Enable
128-
μ
s
Interrupt
Enable
USB Bus
Reset /
PS/2 Activity
Intr. Enable
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
Figure 21-1. Global Interrupt Enable Register (Address 0x20)
相關PDF資料
PDF描述
CY7C63743 enCoRe USB Combination Low-Speed USB & PS/2 Peripheral Controller
CY7C63743-PC enCoRe USB Combination Low-Speed USB & PS/2 Peripheral Controller
CY7C63743C enCoRe USB Combination Low-Speed USB and PS/2 Peripheral Controller(enCoRe USB結合低速USB和PS/2外設控制器)
CY7C63723C enCoRe USB Combination Low-Speed USB and PS/2 Peripheral Controller(enCoRe USB結合低速USB和PS/2外設控制器)
CY7C63803 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
相關代理商/技術參數
參數描述
CY7C63723-PXC 功能描述:IC MCU 8K USB/PS2 LS 18DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382
CY7C63723-SC 功能描述:IC MCU 8K LS USB/PS-2 18-SOIC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382
CY7C63723-SCT 制造商:Cypress Semiconductor 功能描述:I/O Controller USB and PS/2 Controller 0.02A 18-Pin SOIC T/R
CY7C63723-SXC 功能描述:IC MCU 8K LS USB/PS-2 18-SOIC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382
CY7C63723-SXCT 制造商:Cypress Semiconductor 功能描述:I/O Controller USB and PS/2 Controller 0.02A 18-Pin SOIC T/R
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*