參數資料
型號： CY7C63723-PC
廠商： CYPRESS SEMICONDUCTOR CORP
元件分類： 微控制器/微處理器
英文描述： enCoRe USB Combination Low-Speed USB & PS/2 Peripheral Controller
中文描述： 8-BIT, OTPROM, 12 MHz, RISC MICROCONTROLLER, PDIP18
封裝： 0.300 INCH, PLASTIC, DIP-18
文件頁數： 9/58頁
文件大小： 1236K
代理商： CY7C63723-PC
FOR
FOR
enCoRe
USB CY7C63722/23
CY7C63743
Document #: 38-08022 Rev. **
Page 9 of 58
The return from subroutine (RET) instruction restores the program counter, but not the flags, from program stack and decrements
the PSP by two.
Note that there are restrictions in using the JMP, CALL, and INDEX instructions across the 4-KB boundary of the program memory.
Refer to the
CYASM Assembler User’s Guide
for a detailed description.
6.5
The data stack pointer (DSP) supports PUSH and POP instructions that use the data stack for temporary storage. A PUSH
instruction will pre-decrement the DSP, then write data to the memory location addressed by the DSP. A POP instruction will read
data from the memory location addressed by the DSP, then post-increment the DSP.
During a reset, the Data Stack Pointer will be set to zero. A PUSH instruction when DSP equals zero will write data at the top of
the data RAM (address 0xFF). This would write data to the memory area reserved for a FIFO for USB endpoint 0. In non-USB
applications, this works fine and is not a problem.
For USB applications, the firmware should set the DSP to an appropriate location to avoid a memory conflict with RAM dedicated
to USB FIFOs. The memory requirements for the USB endpoints are shown in Section 8.2. For example, assembly instructions
to set the DSP to 20h (giving 32 bytes for program and data stack combined) are shown below:
MOV A,20h
; Move 20 hex into Accumulator (must be D8h or less to avoid USB FIFOs)
SWAP A,DSP ; swap accumulator value into DSP register
8-bit Data Stack Pointer (DSP)
6.6
The CY7C637xx microcontrollers support three addressing modes for instructions that require data operands: data, direct, and
indexed.
Address Modes
6.6.1
The “Data” address mode refers to a data operand that is actually a constant encoded in the instruction. As an example, consider
the instruction that loads A with the constant 0x30:
MOV A, 30h
This instruction will require two bytes of code where the first byte identifies the “MOV A” instruction with a data operand as the
second byte. The second byte of the instruction will be the constant “0xE8h”. A constant may be referred to by name if a prior
“EQU” statement assigns the constant value to the name. For example, the following code is equivalent to the example shown
above:
DSPINIT: EQU 30h
MOV A,DSPINIT
Data
6.6.2
“Direct” address mode is used when the data operand is a variable stored in SRAM. In that case, the one byte address of the
variable is encoded in the instruction. As an example, consider an instruction that loads A with the contents of memory address
location 0x10h:
MOV A, [10h]
In normal usage, variable names are assigned to variable addresses using “EQU” statements to improve the readability of the
assembler source code. As an example, the following code is equivalent to the example shown above:
buttons: EQU 10h
MOV A,[buttons]
Direct
6.6.3
“Indexed” address mode allows the firmware to manipulate arrays of data stored in SRAM. The address of the data operand is
the sum of a constant encoded in the instruction and the contents of the “X” register. In normal usage, the constant will be the
“base” address of an array of data and the X register will contain an index that indicates which element of the array is actually
addressed:
array: EQU 10h
MOV X,3
MOV A,[x+array]
This would have the effect of loading A with the fourth element of the SRAM “array” that begins at address 0x10h. The fourth
element would be at address 0x13h.
Indexed
相關PDF資料
PDF描述
CY7C63743 enCoRe USB Combination Low-Speed USB & PS/2 Peripheral Controller
CY7C63743-PC enCoRe USB Combination Low-Speed USB & PS/2 Peripheral Controller
CY7C63743C enCoRe USB Combination Low-Speed USB and PS/2 Peripheral Controller(enCoRe USB結合低速USB和PS/2外設控制器)
CY7C63723C enCoRe USB Combination Low-Speed USB and PS/2 Peripheral Controller(enCoRe USB結合低速USB和PS/2外設控制器)
CY7C63803 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
相關代理商/技術參數
參數描述
CY7C63723-PXC 功能描述:IC MCU 8K USB/PS2 LS 18DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382
CY7C63723-SC 功能描述:IC MCU 8K LS USB/PS-2 18-SOIC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382
CY7C63723-SCT 制造商:Cypress Semiconductor 功能描述:I/O Controller USB and PS/2 Controller 0.02A 18-Pin SOIC T/R
CY7C63723-SXC 功能描述:IC MCU 8K LS USB/PS-2 18-SOIC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382
CY7C63723-SXCT 制造商:Cypress Semiconductor 功能描述:I/O Controller USB and PS/2 Controller 0.02A 18-Pin SOIC T/R
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*