參數資料
型號： CY7C63723-SC
廠商： CYPRESS SEMICONDUCTOR CORP
元件分類： 微控制器/微處理器
英文描述： enCoRe USB Combination Low-Speed USB & PS/2 Peripheral Controller
中文描述： 8-BIT, OTPROM, 12 MHz, RISC MICROCONTROLLER, PDSO18
封裝： 0.300 INCH, PLASTIC, MO-119, SOIC-18
文件頁數： 42/58頁
文件大?。?/td> 1236K
代理商： CY7C63723-SC
FOR
FOR
enCoRe
USB CY7C63722/23
CY7C63743
Document #: 38-08022 Rev. **
Page 42 of 58
22.0
The following tables give details on mode setting for the USB Serial Interface Engine (SIE) for both the control endpoint (EP0)
and non-control endpoints (EP1 and EP2).
USB Mode Tables
Note:
3.
STALL bit is the bit 7 of the USB Non-Control Device Endpoint Mode registers. Refer to Section 14.3 for more explanation.
Mode Column:
The 'Mode' column contains the mnemonic names given to the modes of the endpoint. The mode of the endpoint is determined
by the four-bit binaries in the 'Encoding' column as discussed below. The Status IN and Status OUT modes represent the status
IN or OUT stage of the control transfer.
Encoding Column:
The contents of the 'Encoding' column represent the Mode Bits [3:0] of the Endpoint Mode Registers (
Figure 14-2
and
Figure 14-3
). The endpoint modes determine how the SIE responds to different tokens that the host sends to the endpoints. For
example, if the Mode Bits [3:0] of the Endpoint 0 Mode Register (
Figure 14-2
) are set to '0001', which is NAK IN/OUT mode as
shown in
Table 22-1
above, the SIE of the part will send an ACK handshake in response to SETUP tokens and NAK any IN or
OUT tokens. For more information on the functionality of the Serial Interface Engine (SIE), see Section 13.0.
SETUP, IN, and OUT Columns:
Depending on the mode specified in the 'Encoding' column, the 'SETUP', 'IN', and 'OUT' columns contain the device SIE's
responses when the endpoint receives SETUP, IN, and OUT tokens respectively.
A 'Check' in the Out column means that upon receiving an OUT token the SIE checks to see whether the OUT is of zero length
and has a Data Toggle (Data1/0) of 1. If these conditions are true, the SIE responds with an ACK. If any of the above conditions
is not met, the SIE will respond with either a STALL or Ignore.
Table 22-3
gives a detailed analysis of all possible cases.
A 'TX Count' entry in the IN column means that the SIE will transmit the number of bytes specified in the Byte Count Bit [3:0] of
the Endpoint Count Register (
Figure 14-4
) in response to any IN token.
Table 22-1. USB Register Mode Encoding for Control and Non-Control Endpoints
Mode
Encoding
0000
0001
SETUP
Ignore
Accept
IN
OUT
Ignore
NAK
Comments
Ignore all USB traffic to this endpoint
On Control endpoint, after successfully sending an ACK
handshake to a SETUP packet, the SIE forces the
endpoint mode (from modes other than 0000) to 0001.
The mode is also changed by the SIE to 0001 from mode
1011 on issuance of ACK handshake to an OUT.
For Control endpoints
For Control endpoints
For Control endpoints
Reserved
For Control Endpoints
Reserved
In mode 1001, after sending an ACK handshake to an
OUT, the SIE changes the mode to 1000
This mode is changed by the SIE to mode 1000 on
issuance of ACK handshake to an OUT
Disable
NAK IN/OUT
Ignore
NAK
Status OUT Only
STALL IN/OUT
Ignore IN/OUT
Reserved
Status IN Only
Reserved
NAK OUT
0010
0011
0100
0101
0110
0111
1000
Accept
Accept
Accept
Ignore
Accept
Ignore
Ignore
STALL
STALL
Ignore
Ignore
TX 0 Byte
TX Count
Ignore
Check
STALL
Ignore
Always
STALL
Ignore
NAK
ACK OUT(
STALL
[3]
=0)
ACK OUT
(STALL
[3]
=1)
NAK OUT - Status IN
ACK OUT - NAK IN
1001
1001
1010
1011
Ignore
Ignore
Accept
Accept
Ignore
Ignore
TX 0 Byte
NAK
ACK
STALL
NAK
ACK
This mode is changed by the SIE to mode 0001 on
issuance of ACK handshake to an OUT
An ACK from mode 1101 changes the mode to 1100
This mode is changed by the SIE to mode 1100 on
issuance of ACK handshake to an IN
An ACK from mode 1111 changes the mode to 1110
This mode is changed by the SIE to mode 1110 on
issuance of ACK handshake to an IN
NAK IN
ACK IN
(STALL
[3]
=0)
ACK IN(
STALL
[3]
=1)
NAK IN - Status OUT
ACK IN - Status OUT
1100
Ignore
Ignore
Ignore
Accept
Accept
NAK
Ignore
Ignore
Ignore
Check
Check
1101
1101
1110
1111
TX Count
STALL
NAK
TX Count
相關PDF資料
PDF描述
CY7C63743-SC enCoRe USB Combination Low-Speed USB & PS/2 Peripheral Controller
CY7C63722 enCoRe USB Combination Low-Speed USB & PS/2 Peripheral Controller
CY7C63723 enCoRe USB Combination Low-Speed USB & PS/2 Peripheral Controller
CY7C63723-PC enCoRe USB Combination Low-Speed USB & PS/2 Peripheral Controller
CY7C63743 enCoRe USB Combination Low-Speed USB & PS/2 Peripheral Controller
相關代理商/技術參數
參數描述
CY7C63723-SCT 制造商:Cypress Semiconductor 功能描述:I/O Controller USB and PS/2 Controller 0.02A 18-Pin SOIC T/R
CY7C63723-SXC 功能描述:IC MCU 8K LS USB/PS-2 18-SOIC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382
CY7C63723-SXCT 制造商:Cypress Semiconductor 功能描述:I/O Controller USB and PS/2 Controller 0.02A 18-Pin SOIC T/R
CY7C63743C-PXC 功能描述:輸入/輸出控制器接口集成電路 USB Combo Lo Spd PS/2 Periphrl Cntrlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
CY7C63743C-QXC 功能描述:輸入/輸出控制器接口集成電路 LO Speed 3 Endpoint USB COM RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*