參數資料
型號： CY7C63723C
廠商： Cypress Semiconductor Corp.
英文描述： enCoRe USB Combination Low-Speed USB and PS/2 Peripheral Controller(enCoRe USB結合低速USB和PS/2外設控制器)
中文描述： 的enCoRe USB的組合低速USB和PS / 2外設控制器（的enCoRe的USB結合低速的USB和的PS / 2外設控制器）
文件頁數： 20/49頁
文件大?。?/td> 1942K
代理商： CY7C63723C
CY7C63722C
CY7C63723C
CY7C63743C
FOR
FOR
Document #: 38-08022 Rev. *C
Page 20 of 49
15.0
USB Regulator Output
The VREG pin provides a regulated output for connecting the
pull-up resistor required for USB operation. For USB, a 1.5-k
resistor is connected between the D– pin and the V
REG
voltage, to indicate low-speed USB operation. Since the
VREG output has an internal series resistance of approxi-
mately 200
, the external pull-up resistor required is R
PU
(see
Section 25.0).
The regulator output is placed in a high-impedance state at
reset, and must be enabled by firmware by setting the VREG
Enable bit in the USB Status and Control Register
(
Figure 13-1
). This simplifies the design of a combination
PS/2-USB device, since the USB pull-up resistor can be left in
place during PS/2 operation without loading the PS/2 line. In
this mode, the V
REG
pin can be used as an input and its state
can be read at port P2.0. Refer to
Figure 12-8
for the Port 2
data register. This input has a TTL threshold.
In suspend mode, the regulator is automatically disabled. If
VREG Enable bit is set (
Figure 13-1
), the VREG pin is pulled
up to V
CC
with an internal 6.2-k
resistor. This holds the
proper V
OH
state in suspend mode
Note that enabling the device for USB (by setting the Device
Address Enable bit,
Figure 14-1
) activates the internal
regulator, even if the VREG Enable bit is cleared to 0. This
insures proper USB signaling in the case where the VREG pin
is used as an input, and an external regulator is provided for
the USB pull-up resistor. This also limits the swing on the D–
and D+ pins to about 1V above the internal regulator voltage,
so the Device Address Enable bit normally should only be set
for USB operating modes.
The regulator output is only designed to provide current for the
USB pull-up resistor. In addition, the output voltage at the
VREG pin is effectively disconnected when the CY7C637xxC
device transmits USB from the internal SIE. This means that
the VREG pin does not provide a stable voltage during
transmits, although this does not affect USB signaling.
16.0
PS/2 Operation
The CY7C637xxC parts are optimized for combination USB or
PS/2 devices, through the following features:
1. USB D+ and D– lines can also be used for PS/2 SCLK and
SDATA pins, respectively. With USB disabled, these lines
can be placed in a high-impedance state that will pull up to
V
CC
. (Disable USB by clearing the Address Enable bit of
the USB Device Address Register,
Figure 14-1
).
2. An interrupt is provided to indicate a long LOW state on the
SDATA pin. This eliminates the need to poll this pin to check
for PS/2 activity. Refer to Section 21.3 for more details.
3. Internal PS/2 pull-up resistors can be enabled on the SCLK
and SDATA lines, so no GPIO pins are required for this task
(bit 7, USB Status and Control Register,
Figure 13-1
).
4. The controlled slew rate outputs from these pins apply to
both USB and PS/2 modes to minimize EMI.
5. The state of the SCLK and SDATA pins can be read, and
can be individually driven LOW in an open drain mode. The
pins are read at bits [5:4] of Port 2, and are driven with the
Control Bits [2:0] of the USB Status and Control Register.
6. The V
REG
pin can be placed into a high-impedance state,
so that a USB pull-up resistor on the D–/SDATA pin will not
interfere with PS/2 operation (bit 6, USB Status and Control
Register).
The PS/2 on-chip support circuitry is illustrated in
Figure 16-1
.
Figure 16-1. Diagram of USB-PS/2 System Connections
D–/SDATA
D+/SCLK
5 k
3.3V
Regulator
5 k
V
CC
USB - PS/2
Driver
1.3 k
VREG
VREG Enable
PS/2 Pull-up
Enable
Port 2.0
On-chip
Off-chip
Port 2.5
Port 2.4
200
相關PDF資料
PDF描述
CY7C63803 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
CY7C63310 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
CY7C63801 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
CY7C63823 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
CY7C63813 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
相關代理商/技術參數
參數描述
CY7C63723C-PXC 功能描述:輸入/輸出控制器接口集成電路 USB/PS/2 Combo LoSpd Peripheral Controlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
CY7C63723C-SXC 功能描述:輸入/輸出控制器接口集成電路 USB/PS/2 Combo LoSpd Peripheral Controlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
CY7C63723C-SXCT 功能描述:輸入/輸出控制器接口集成電路 USB/PS/2 Combo LoSpd Peripheral Controlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
CY7C63723-PC 功能描述:IC MCU 8K LS USB/PS-2 18-DIP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382
CY7C63723-PXC 功能描述:IC MCU 8K USB/PS2 LS 18DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*