參數資料
型號： CY7C63743C
廠商： Cypress Semiconductor Corp.
英文描述： enCoRe USB Combination Low-Speed USB and PS/2 Peripheral Controller(enCoRe USB結合低速USB和PS/2外設控制器)
中文描述： 的enCoRe USB的組合低速USB和PS / 2外設控制器（的enCoRe的USB結合低速的USB和的PS / 2外設控制器）
文件頁數： 33/49頁
文件大?。?/td> 1942K
代理商： CY7C63743C
CY7C63722C
CY7C63723C
CY7C63743C
FOR
FOR
Document #: 38-08022 Rev. *C
Page 33 of 49
Mode Column:
The 'Mode' column contains the mnemonic names given to the
modes of the endpoint. The mode of the endpoint is deter-
mined by the four-bit binaries in the 'Encoding' column as
discussed below. The Status IN and Status OUT modes
represent the status IN or OUT stage of the control transfer.
Encoding Column:
The contents of the 'Encoding' column represent the Mode Bits
[3:0] of the Endpoint Mode Registers (
Figure 14-2
and
Figure 14-3
). The endpoint modes determine how the SIE
responds to different tokens that the host sends to the
endpoints. For example, if the Mode Bits [3:0] of the Endpoint
0 Mode Register (
Figure 14-2
) are set to '0001', which is NAK
IN/OUT mode as shown in
Table 22-1
above, the SIE of the
part will send an ACK handshake in response to SETUP
tokens and NAK any IN or OUT tokens. For more information
on the functionality of the Serial Interface Engine (SIE), see
Section 13.0.
SETUP, IN, and OUT Columns:
Depending on the mode specified in the 'Encoding' column,
the 'SETUP', 'IN', and 'OUT' columns contain the device SIE's
responses when the endpoint receives SETUP, IN, and OUT
tokens respectively.
A 'Check' in the Out column means that upon receiving an
OUT token the SIE checks to see whether the OUT is of zero
length and has a Data Toggle (Data1/0) of 1. If these condi-
tions are true, the SIE responds with an ACK. If any of the
above conditions is not met, the SIE will respond with either a
STALL or Ignore.
Table 22-3
gives a detailed analysis of all
possible cases.
A 'TX Count' entry in the IN column means that the SIE will
transmit the number of bytes specified in the Byte Count Bit
[3:0] of the Endpoint Count Register (
Figure 14-4
) in response
to any IN token.
A 'TX 0 Byte' entry in the IN column means that the SIE will
transmit a zero byte packet in response to any IN sent to the
endpoint. Sending a 0 byte packet is to complete the status
stage of a control transfer.
An 'Ignore' means that the device sends no handshake tokens.
An 'Accept' means that the SIE will respond with an ACK to a
valid SETUP transaction.
Comments Column:
Some Mode Bits are automatically changed by the SIE in
response to many USB transactions. For example, if the Mode
Bits [3:0] are set to '1111' which is ACK IN-Status OUT mode
as shown in
Table 22-1
, the SIE will change the endpoint Mode
Bits [3:0] to NAK IN-Status OUT mode (1110) after ACKing a
valid status stage OUT token. The firmware needs to update
the mode for the SIE to respond appropriately. See
Table 22-1
for more details on what modes will be changed by the SIE.
Any SETUP packet to an enabled endpoint with mode set to
accept SETUPs will be changed by the SIE to 0001 (NAKing).
Any mode set to accept a SETUP will send an ACK handshake
to a valid SETUP token.
A disabled endpoint will remain disabled until changed by
firmware, and all endpoints reset to the Disabled mode (0000).
Firmware normally enables the endpoint mode after a SetCon-
figuration request.
The control endpoint has three status bits for identifying the
token type received (SETUP, IN, or OUT), but the endpoint
must be placed in the correct mode to function as such.
Non-control endpoints should not be placed into modes that
accept SETUPs.
Table 22-2. Decode table for
Table 22-3
: “Details of Modes for Differing Traffic Conditions”
Endpoint Mode
Encoding
Properties of incoming
packet
Changes to the internal register made by the SIE as a result of
the incoming token
Interrupt
End Point
Mode
3
2
1
0
Token
count
buffer
dval
DTOG
DVAL
COUNT
Setup
In
Out
ACK
3
2
1
0
Response
Int
Bit[3:0],
Figure 14-4
SIE’s Response
Data Valid (Bit 6,
Figure 14-4
)
Endpoint Mode changed
by the SIE.
Data 0/1 (Bit 7,
Figure 14-4
)
Received Token
(SETUP, IN,OUT)
The validity of the received data
Acknowledge transaction completed
(Bit4,
Figure 14-2
/3)
The quality status of the DMA buffer
PID Status Bits
(Bit[7:5],
Figure 14-2
)
The number of received bytes
Legend:
UC: unchanged
TX: transmit
TX0: transmit 0-length packet
x: don’t care
RX: receive
available for Control endpoint only
相關PDF資料
PDF描述
CY7C63723C enCoRe USB Combination Low-Speed USB and PS/2 Peripheral Controller(enCoRe USB結合低速USB和PS/2外設控制器)
CY7C63803 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
CY7C63310 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
CY7C63801 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
CY7C63823 enCoRe II Low-Speed USB Peripheral Controller(enCoRe II低速USB外設控制器)
相關代理商/技術參數
參數描述
CY7C63743C-PXC 功能描述:輸入/輸出控制器接口集成電路 USB Combo Lo Spd PS/2 Periphrl Cntrlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
CY7C63743C-QXC 功能描述:輸入/輸出控制器接口集成電路 LO Speed 3 Endpoint USB COM RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
CY7C63743C-SXC 功能描述:輸入/輸出控制器接口集成電路 USB Combo Lo Spd PS/2 Periphrl Cntrlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
CY7C63743C-SXCT 功能描述:輸入/輸出控制器接口集成電路 USB/PS/2 Combo LoSpd Peripheral Controlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
CY7C63743-PC 功能描述:IC MCU 8K LS USB/PS-2 24-DIP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*