參數資料
型號: CY7C67200
廠商: Cypress Semiconductor Corp.
英文描述: EZ-OTG Programmable USB On-The-Go Host/Peripheral Controller(EZ-OTG可編程USB On-The-Go主機/外圍設備控制器)
中文描述: 的EZ - OTG公司可編程的USB On - The - Go的主機/外設控制器(的EZ - OTG公司可編程的USB On - The - Go的主機/外圍設備控制器)
文件頁數: 27/82頁
文件大?。?/td> 1719K
代理商: CY7C67200
CY7C67200
Document #: 38-08014 Rev. *F
Page 27 of 82
VBUS Interrupt Flag
(Bit 15)
The VBUS Interrupt Flag bit indicates the status of the OTG VBUS interrupt (only for Port 1A). When enabled this interrupt triggers
on both the rising and falling edge of VBUS at 4.4V. This bit is only available for Host 1 and is a reserved bit in Host 2.
1:
Interrupt triggered
0:
Interrupt did not trigger
ID Interrupt Flag
(Bit 14)
The ID Interrupt Flag bit indicates the status of the OTG ID interrupt (only for Port 1A). When enabled this interrupt triggers on
both the rising and falling edge of the OTG ID pin. This bit is only available for Host 1 and is a reserved bit in Host 2.
1:
Interrupt triggered
0:
Interrupt did not trigger
SOF/EOP Interrupt Flag
(Bit 9)
The SOF/EOP Interrupt Flag bit indicates the status of the SOF/EOP Timer interrupt. This bit triggers ‘1’ when the SOF/EOP timer
expires.
1:
Interrupt triggered
0:
Interrupt did not trigger
Port A Wake Interrupt Flag
(Bit 6)
The Port A Wake Interrupt Flag bit indicates remote wakeup on PortA
1:
Interrupt triggered
0:
Interrupt did not trigger
Port A Connect Change Interrupt Flag
(Bit 4)
The Port A Connect Change Interrupt Flag bit indicates the status of the Connect Change interrupt on Port A. This bit triggers ‘1’
on either a rising edge or falling edge of a USB Reset condition (device inserted or removed). Together with the Port A SE0 Status
bit, it can be determined whether a device was inserted or removed.
1:
Interrupt triggered
0:
Interrupt did not trigger
Port A SE0 Status
(Bit 2)
The Port A SE0 Status bit indicates if Port A is in an SE0 state or not. Together with the Port A Connect change Interrupt Flag
bit, it can be determined whether a device was inserted (non-SE0 condition) or removed (SE0 condition).
1:
SE0 condition
0:
Non-SE0 condition
Done Interrupt Flag
(Bit 0)
The Done Interrupt Flag bit indicates the status of the USB Transfer Done interrupt. The USB Transfer Done triggers when either
the host responding with and ACK, or a device responds with any of the following: ACK, NAK, STALL, or Timeout. This interrupt
is used for both Port A and Port B.
1:
Interrupt triggered
0:
Interrupt did not trigger
相關PDF資料
PDF描述
CY7C68320C EZ-USB AT2LP USB 2.0 to ATA/ATAPI Bridge(EZ-USB AT2LP USB 2.0到ATA/ATAPI橋接器)
CY7C68301C EZ-USB AT2LP USB 2.0 to ATA/ATAPI Bridge(EZ-USB AT2LP USB 2.0到ATA/ATAPI橋接器)
CY7C68300C EZ-USB AT2LP USB 2.0 to ATA/ATAPI Bridge(EZ-USB AT2LP USB 2.0到ATA/ATAPI橋接器)
CY7C68321C EZ-USB AT2LP USB 2.0 to ATA/ATAPI Bridge(EZ-USB AT2LP USB 2.0到ATA/ATAPI橋接器)
CY8C20434 PSoC Mixed-Signal Array(PSoC混合信號陣列)
相關代理商/技術參數
參數描述
CY7C672001-48BAXI 功能描述:8位微控制器 -MCU CY7C672001-48BAXI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
CY7C672001-48BAXIT 功能描述:8位微控制器 -MCU CY7C672001-48BAXIT RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
CY7C67200-48BAXI 功能描述:USB 接口集成電路 LO PWR OTG IND RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
CY7C67200-48BAXIT 功能描述:USB 接口集成電路 LO PWR OTG IND RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
CY7C67300-100AI 制造商:Cypress Semiconductor 功能描述:INTERFACE MISC