- 您現在的位置：買賣IC網 > PDF目錄379097 > CY7C68300C (Cypress Semiconductor Corp.) EZ-USB AT2LP USB 2.0 to ATA/ATAPI Bridge(EZ-USB AT2LP USB 2.0到ATA/ATAPI橋接器) PDF資料下載
參數資料
| 型號： | CY7C68300C |
| 廠商： | Cypress Semiconductor Corp. |
| 英文描述： | EZ-USB AT2LP USB 2.0 to ATA/ATAPI Bridge(EZ-USB AT2LP USB 2.0到ATA/ATAPI橋接器) |
| 中文描述： | 的EZ - USB AT2LP產品的USB 2.0的ATA / ATAPI橋（的EZ - USB AT2LP產品的USB 2.0到ATA / ATAPI接口橋接器） |
| 文件頁數： | 15/42頁 |
| 文件大?。?/td> | 761K |
| 代理商： | CY7C68300C |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
CY7C68300C/CY7C68301C
CY7C68320C/CY7C68321C
Document 001-05809 Rev. *A
Page 15 of 42
HID Functions for Button Controls
Cypress’s CY7C68320C/CY7C68321C has the capability of
supporting Human Interface Device (HID) signaling to the
host.
If there is a HID descriptor in the configuration data, the GPIO
pins that are set as inputs are polled by the AT2LP logic
approximately every 17 ms (depending on other internal
interrupt routines). If a change is detected in the state of any
HID-enabled GPIO, an HID report is sent through EP1 to the
host. The report format for byte 0 and byte 1 are shown in
Table 5
.
The ability to add buttons to a mass storage solution opens
new applications for data backup and other device-side notifi-
cation to the host. The AT2LP Blaster software, found in the
CY4615C files, provides an easy way to enable and modify the
HID features of the AT2LP.
GPIO pins can be individually set as inputs or outputs, with
byte 0x09 of the configuration data, allowing for a mix of HID
and general purpose outputs. GPIOs that are not configured
as inputs are reported with a value of ‘0’ in the HID data. The
RESERVED bits’ values must be ignored, and Cypress recom-
mends using a bitmask in software to filter out unused HID
data.
Note that if using the 56-pin package, the reported GPIO[5:3]
values must be ignored because the pins are not actually
present.
Functional Overview
Chip functionally is described in the subsequent sections.
USB Signaling Speed
AT2LP operates at the following two rates defined in the
USB
Specification Revision 2.0
dated April 27, 2000:
Full-speed, with a signaling bit rate of 12 Mbits/sec.
High-speed, with a signaling bit rate of 480 Mbits/sec.
AT2LP does not operate at the low-speed signaling rate of 1.5
Mbits/sec.
ATA Interface
The ATA/ATAPI port on the AT2LP is compatible with the
Infor-
mation Technology–AT Attachment with Packet Interface–6
(ATA/ATAPI-6) Specification, T13/1410D Rev 2a
. The AT2LP
supports both ATAPI packet commands as well as ATA
commands (by use of ATA Command Blocks), as outlined in
“ATA Command Block (ATACB)” on page 15
. Refer to the
USB
Mass Storage Class (MSC) Bulk Only Transport (BOT)
Speci-
fication for information on Command Block formatting.
Additionally, the AT2LP translates
ATAPI SFF-8070i
commands to ATA commands for seamless integration of ATA
devices with generic Mass Storage Class BOT drivers.
ATA Command Block (ATACB)
The ATA Command Block (ATACB) functionality provides a
means of passing ATA commands and ATA register accesses
to the attached device for execution. ATACB commands are
transferred in the Command Block Wrapper Command Block
(CBWCB) portion of the Command Block Wrapper (CBW).
The ATACB is distinguished from other command blocks by
having the first two bytes of the command block match the
bVSCBSignature and bVSCBSubCommand values that are
defined in
Table 6
. Only command blocks that have a valid
bVSCBSignature and bVSCBSubCommand are interpreted
as ATA Command Blocks. All other fields of the CBW and
restrictions on the CBWCB remain as defined in the USB Mass
Storage Class Bulk-Only Transport Specification. The ATACB
must be 16 bytes in length. The following table and text defines
the fields of the ATACB.
Table 5. HID Data Bitmap
USB Interrupt Data Byte 1
5
4
USB Interrupt Data Byte 0
5
4
7
6
3
2
1
0
7
6
3
2
1
0
R
R
R
R
R
R
U
V
R
R
G
G
G
G
G
G
相關PDF資料 |
PDF描述 |
|---|---|
| CY7C68321C | EZ-USB AT2LP USB 2.0 to ATA/ATAPI Bridge(EZ-USB AT2LP USB 2.0到ATA/ATAPI橋接器) |
| CY8C20434 | PSoC Mixed-Signal Array(PSoC混合信號陣列) |
| CY8C20234 | PSoC Mixed-Signal Array(PSoC混合信號陣列) |
| CY8C20334 | PSoC Mixed-Signal Array(PSoC混合信號陣列) |
| CY8C22213-24PVIT | PSoC Mixed Signal Array |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY7C68300C-100AXC | 功能描述:接口 - 專用 USB Hi Spd Peripherals RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| CY7C68300C-56LFXC | 功能描述:USB 接口集成電路 USB Hi Spd Peripherals RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| CY7C68300C-56LTXC | 功能描述:USB 接口集成電路 AT2LP HS-USB RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| CY7C68300C-56LTXCKA | 制造商:Rochester Electronics LLC 功能描述: 制造商:Cypress Semiconductor 功能描述: |
| CY7C68300C-56LTXCKM | 制造商:Cypress Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。