參數資料
型號： CY7C68300C
廠商： Cypress Semiconductor Corp.
英文描述： EZ-USB AT2LP USB 2.0 to ATA/ATAPI Bridge(EZ-USB AT2LP USB 2.0到ATA/ATAPI橋接器)
中文描述： 的EZ - USB AT2LP產品的USB 2.0的ATA / ATAPI橋（的EZ - USB AT2LP產品的USB 2.0到ATA / ATAPI接口橋接器）
文件頁數： 16/42頁
文件大?。?/td> 761K
代理商： CY7C68300C
CY7C68300C/CY7C68301C
CY7C68320C/CY7C68321C
Document 001-05809 Rev. *A
Page 16 of 42
Table 6. ATACB Field Descriptions
Byte
0
Field Name
Field Description
bVSCBSignature
This field indicates to the CY7C68300C/CY7C68301C that the ATACB
contains a vendor-specific command block. This value of this field must match
the value in EEPROM address 0x04 for the command to be recognized as a
vendor-specific ATACB command.
This field must be set to 0x24 for ATACB commands.
This field controls the execution of the ATACB according to the bitfield values:
Bit 7
IdentifyPacketDevice
– This bit indicates that the data phase of the
command contains ATAPI (0xA1) or ATA (0xEC) IDENTIFY device data.
Setting IdentifyPacketDevice when the data phase does not contain IDENTIFY
device data results in unspecified device behavior.
0 = Data phase does not contain IDENTIFY device data
1 = Data phase contains ATAPI or ATA IDENTIFY device data
Bit 6
UDMACommand
– This bit enables supported UDMA device transfers.
Setting this bit when a non-UDMA capable device is attached results in
undetermined behavior.
0 = Do not use UDMA device transfers (only use PIO mode)
1 = Use UDMA device transfers
Bit 5
DEVOverride
– This bit determines whether the DEV bit value is taken
from the value assigned to the LUN during startup or from the ATACB.
0 = The DEV bit is taken from the value assigned to the LUN during startup
1 = The DEV bit is taken from the ATACB field 0x0B, bit 4
Bit 4
DErrorOverride
– This bit controls the device error override feature. This
bit must not be set during a bmATACBActionSelect TaskFileRead.
0 = Data accesses are halted if a device error is detected
1 = Data accesses are not halted if a device error is detected
Bit 3
PErrorOverride
– This bit controls the phase error override feature. This
bit must not be set during a bmATACBActionSelect TaskFileRead.
0 = Data accesses are halted if a phase error is detected
1 = Data accesses are not halted if a phase error is detected
Bit 2
PollAltStatOverride
– This bit determines whether or not the Alternate
Status register is polled and the BSY bit is used to qualify the ATACB operation.
0 = The AltStat register is polled until BSY=0 before proceeding with the ATACB
operation
1 = The ATACB operation is executed without polling the AltStat register.
Bit 1
DeviceSelectionOverride
– This bit determines when the device selection
is performed in relation to the command register write accesses.
0 = Device selection is performed before command register write accesses
1 = Device selection is performed following command register write accesses
Bit 0
TaskFileRead
– This bit determines whether or not the taskfile register
data selected in bmATACBRegisterSelect is returned. If this bit is set, the
dCBWDataTransferLength field must be set to 8.
0 = Execute ATACB command and data transfer (if any)
1 = Only read taskfile registers selected in bmATACBRegisterSelect and return
0x00h for all others. The format of the 8 bytes of returned data is as follows:
Address offset 0x00 (0x3F6) – Alternate Status
Address offset 0x01 (0x1F1) – Features/Error
Address offset 0x02 (0x1F2) – Sector Count
Address offset 0x03 (0x1F3) – Sector Number
Address offset 0x04 (0x1F4) – Cylinder Low
Address offset 0x05 (0x1F5) – Cylinder High
Address offset 0x06 (0x1F6) – Device/Head
Address offset 0x07 (0x1F7) – Command/Status
1
2
bVSCBSubCommand
bmATACBActionSelect
相關PDF資料
PDF描述
CY7C68321C EZ-USB AT2LP USB 2.0 to ATA/ATAPI Bridge(EZ-USB AT2LP USB 2.0到ATA/ATAPI橋接器)
CY8C20434 PSoC Mixed-Signal Array(PSoC混合信號陣列)
CY8C20234 PSoC Mixed-Signal Array(PSoC混合信號陣列)
CY8C20334 PSoC Mixed-Signal Array(PSoC混合信號陣列)
CY8C22213-24PVIT PSoC Mixed Signal Array
相關代理商/技術參數
參數描述
CY7C68300C-100AXC 功能描述:接口 - 專用 USB Hi Spd Peripherals RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
CY7C68300C-56LFXC 功能描述:USB 接口集成電路 USB Hi Spd Peripherals RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
CY7C68300C-56LTXC 功能描述:USB 接口集成電路 AT2LP HS-USB RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
CY7C68300C-56LTXCKA 制造商:Rochester Electronics LLC 功能描述: 制造商:Cypress Semiconductor 功能描述:
CY7C68300C-56LTXCKM 制造商:Cypress Semiconductor 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*