參數資料
型號: CY7C68300C
廠商: Cypress Semiconductor Corp.
英文描述: EZ-USB AT2LP USB 2.0 to ATA/ATAPI Bridge(EZ-USB AT2LP USB 2.0到ATA/ATAPI橋接器)
中文描述: 的EZ - USB AT2LP產品的USB 2.0的ATA / ATAPI橋(的EZ - USB AT2LP產品的USB 2.0到ATA / ATAPI接口橋接器)
文件頁數: 33/42頁
文件大?。?/td> 761K
代理商: CY7C68300C
CY7C68300C/CY7C68301C
CY7C68320C/CY7C68321C
Document 001-05809 Rev. *A
Page 33 of 42
Note
: More than 0X100 bytes of configuration are shown for example only. The AT2LP only supports addresses up to 0xFF.
Programming the EEPROM
There are three methods of programming the EEPROM:
Stand-alone EEPROM programmer
Vendor-specific USB commands, listed in
Table 12
In-system programming (for example, bed-of-nails tester)
Any vendor-specific USB write request to the Serial ROM device configuration space simultaneously update internal configuration
register values as well. If the I
2
C device is programmed without vendor specific USB commands, the AT2LP must be synchro-
nously reset (toggle RESET#) before configuration data is reloaded.
The AT2LP supports a subset of the ’slow mode’ specification (100 KHz) required for 24LCXXB EEPROM family device support.
Features such as ’Multi-Master,’ ’Clock Synchronization’ (the SCL pin is output only), ’10-bit addressing,’ and ’CBUS device
support’ are not supported. Vendor-specific USB commands allow the AT2LP to address up to 256 bytes of EEPROM data.
LOAD_CONFIG_DATA
This request enables writes to the AT2LP’s configuration data space. The wIndex field specifies the starting address and the
wLength field denotes the data length in bytes.
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
0Xxx
Device name byte 4
Device name byte 5
Device name byte 6
Device name byte 7
Device name byte 8
Device name byte 9
Device name byte 10
Device name byte 11
Device name byte 12
Device name byte 13
Device name byte 14
Device name byte 15
Device name byte 16
Device name byte 17
Device name byte 18
Device name byte 19
Device name byte 20
Device name byte 21
Device name byte 22
Device name byte 23
Device name byte 24
Unused ROM Space
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
ASCII Character
Amount of unused ROM space varies depending on strings.
’r’ 0x72
’e’ 0x65
’s’ 0x73
’s’ 0x73
’ ’ 0x20
’C’ 0x43
’u’ 0x75
’s’ 0x73
’t’ 0x74
’o’ 0x6f
’m’ 0x6d
’ ’ 0x20
’N’ 0x4e
’a’ 0x61
’m’ 0x6d
’e’ 0x65
’ ’ 0x20
’L’ 0x4c
’U’ 0x55
’N’ 0x4e
’0’ 0x30
0xFF
Table 11.Configuration Data Organization
(continued)
Byte
Address
Configuration
Item Name
Configuration
Item Description
Required
Contents
Variable
Contents
相關PDF資料
PDF描述
CY7C68321C EZ-USB AT2LP USB 2.0 to ATA/ATAPI Bridge(EZ-USB AT2LP USB 2.0到ATA/ATAPI橋接器)
CY8C20434 PSoC Mixed-Signal Array(PSoC混合信號陣列)
CY8C20234 PSoC Mixed-Signal Array(PSoC混合信號陣列)
CY8C20334 PSoC Mixed-Signal Array(PSoC混合信號陣列)
CY8C22213-24PVIT PSoC Mixed Signal Array
相關代理商/技術參數
參數描述
CY7C68300C-100AXC 功能描述:接口 - 專用 USB Hi Spd Peripherals RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
CY7C68300C-56LFXC 功能描述:USB 接口集成電路 USB Hi Spd Peripherals RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
CY7C68300C-56LTXC 功能描述:USB 接口集成電路 AT2LP HS-USB RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
CY7C68300C-56LTXCKA 制造商:Rochester Electronics LLC 功能描述: 制造商:Cypress Semiconductor 功能描述:
CY7C68300C-56LTXCKM 制造商:Cypress Semiconductor 功能描述: