- 您現在的位置：買賣IC網 > PDF目錄353072 > DS-11802D4-895Y Converter PDF資料下載
參數資料
| 型號： | DS-11802D4-895Y |
| 英文描述： | Converter |
| 中文描述： | 轉換器 |
| 文件頁數： | 3/7頁 |
| 文件大?。?/td> | 226K |
| 代理商： | DS-11802D4-895Y |
DS1200
3 of 7
ADDRESS/COMMAND
Each memory transfer consists of a 3-byte input called the address/command. The address/command is
shown in Figure 2. As defined, the first byte of the address/command specifies whether the memory is
written or read. If any one of the bits of the first byte of the address/command fail to meet the exact
pattern of read or write, the cycle is aborted and all future inputs to the tag are ignored until RST is
brought low and then high again to begin a new cycle. The 8-bit pattern for read is 10011101. The second
byte of the address/command describes address inputs A0 in bit 0 through A6 in bit 6. Bit 7 of the second
byte of the address/command word must be set to logic 0. If bit 7 does not equal logic 0, the cycle is
aborted and all future inputs to the tag are ignored until RST is brought low and then high again to begin
a new cycle. The third byte of the address/command (bits 0 through 6) must be set to logic 0 or the cycle
is aborted and all future inputs are ignored until RST is brought low and then high again to begin a new
cycle. Bit 7 of byte 3 of the address/command is used along with address bits A0 through A6 to define
burst mode. When A0 through A6 equals logic 0 and bit 7 of byte 3 of the address command equals logic
1, the tag will enter the burst mode after the address/command sequence is complete.
BURST MODE
Burst mode is when all address bits (A0 to A6) of the address/command are set to logic 0 and bit 7 of byte
3 to logic 1. The burst mode causes 128 consecutive bytes to be read or written. Burst mode terminates
when the RST input is driven low.
RESET AND CLOCK CONTROL
All data transfers are initiated by driving the RST input high. The RST input serves three functions.
First, RST turns on the control logic, which allows access to the shift register for the address/command
sequence. Second, the RST signal provides a power source for the cycle to follow. To meet this
requirement, a drive source for RST of 2mA at 3.8V is required. However if the VCC pin is connected to
a 5V source within nominal limits, then the RST pin is not used as a source of power and input levels
revert to normal VIH and VIL inputs with a drive current requirement of 500mA. Finally, the RST signal
provides a method of terminating either single byte or multiple byte data transfers. A clock cycle is a
sequence of falling edge followed by a rising edge. For data inputs, the data must be valid during the
rising edge of the clock cycle. Address/command bits and data bits are input on the rising edge of the
clock and data bits are output on the falling edge of the clock. All data transfer terminates if the RST
input is low and DQ pin goes to a high-impedance state. When data transfer to the serial RAM chip is
terminated using, RST , the transition of RST must occur while the clock is at high level to avoid
disturbing the last bit of data. Data transfer is illustrated in Figure 3.
DATA INPUT
Following the 24 clock cycles that input an address/command, a data byte is input on the rising edge of
the next eight clock cycles, assuming that the read/write and write/read bits are properly set (for data
input byte 1, bit 0 = 1; bit 1 = 0; bit 2 = 1; bit 3 = 1; bit 4 = 1; bit 5 = 0; bit 6 = 0; bit 7 = 1).
DATA OUTPUT
Following the 24 clock cycles that input the read mode, a data byte is output on the falling edge of the
next eight clock cycles (for data output byte 1, bit 0 = 0; bit 1 = 1; bit 2 = 0; bit 3= 0; bit 4 = 0; bit 5 = 1;
bit 6 = 1; bit 7 = 0).
相關PDF資料 |
PDF描述 |
|---|---|
| DS-11802D4-895Z | Converter |
| DS-11880 | Power Dividers Space Qualified |
| DS1222SN | |
| DS1223 | ELECTRONIC CONFIGURATOR|CMOS|DIP|24PIN|PLASTIC |
| D44H1 | Card Edge Connector; No. of Contacts:72; Pitch Spacing:0.156"; Contact Termination:Solder; Leaded Process Compatible:No; Mounting Hole Dia:0.128"; Peak Reflow Compatible (260 C):No RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS-11802D4-895Z | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Converter |
| DS1181L | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:20MHz to 134MHz Spread-Spectrum Clock Modulator for LCD Panels |
| DS1181LE+ | 功能描述:時鐘發生器及支持產品 Spread-Spectrum CLK Mod for LCD Panels RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| DS1181LE+T | 功能描述:時鐘發生器及支持產品 Spread-Spectrum CLK Mod for LCD Panels RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| DS1182 | 制造商:OSRAM 功能描述:LAMP DULUX WARM 11W |
發布緊急采購，3分鐘左右您將得到回復。