- 您現在的位置：買賣IC網 > PDF目錄379176 > DS1073M-80 1000 Base-T, ±15kV ESD Protection LAN Switches PDF資料下載
參數資料
| 型號： | DS1073M-80 |
| 英文描述： | 1000 Base-T, ±15kV ESD Protection LAN Switches |
| 中文描述： | 3V的EconOscillator /分頻器 |
| 文件頁數： | 8/18頁 |
| 文件大小： | 260K |
| 代理商： | DS1073M-80 |
DS1073
8 of 18
FROM EXTERNAL TO INTERNAL CLOCK
This is accomplished by a low to high transition on the
SELX
pin. In this case the switch is level
triggered, to allow for the possibility of a clock signal not being present at OSCIN. Note therefore, that if
a constant high-level signal is applied to OSCIN it will not be possible to switch over to the internal
reference. (Level triggering was not employed for the switch from internal to external reference as this
approach is slower and the internal clock may be running at a much higher frequency than the maximum
allowed external clock rate). When
SELX
is high and a low level is sensed on EXTCLK, OUT0 will be
held low until a falling edge occurs on INTCLK, then the next rising edge of INTCLK will be routed
through to OUT0.
Figure 8
Depending on the relative timing of the
SELX
signal and the external clock, there may be up to one full
t
Ehigh
period on the output after the rising edge of
SELX
. Then, the “l(fā)ow” time (t
LOW
) between output
pulses will be dependent on the relative timing between t
I
and t
E
. The time interval between the falling
edge of
SELX
and the first rising edge of the externally derived clock is t
SIE
. Approximate maximum and
minimum values of these parameters are:
t
LOW
(min) = t
I
/2
t
LOW
(max) = 3t
I
/2 + t
Elow
t
SIE
(min) = t
I
/2
t
SIE
(max) = 3t
I
/2 + t
Ehigh
NOTE:
In each case there will be a small additional delay due to internal propagation delays.
POWER-DOWN CONTROL
If the PDN bit is set to 1, the
PDN
/
SELX
pin can be used to power-down the device. If
PDN
is high the
device will run normally.
POWER-DOWN
If
PDN
is taken low a power-down sequence is initiated. The “Enabling Sequencer” is used to execute
events in the following sequence:
1.
Disable OUT (same sequence as when OE is used) and reset N counters.
2.
When OUT is low, switch OUT to high-impedance state.
3.
Disable MCLK (and OUT0 if
EN0
bit = 0), switch OUT0 to high impedance state.
4.
Disable internal oscillator and OSCIN buffer.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1077 | 10/100/1000 Base-T Ethernet LAN Switch |
| DS1086 | 10/100/1000 Base-T Ethernet LAN Switch |
| DS1086U | DS1086 Spread-Spectrum EconOscillator |
| DS1086Z | DS1086 Spread-Spectrum EconOscillator |
| DS1094L | 10/100/1000 Base-T Ethernet LAN Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1073-SPECIAL | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Special EconOscillator/Divider |
| DS1073Z-100 | 功能描述:可編程振蕩器 RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS1073Z-10A | 功能描述:可編程振蕩器 RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS1073Z-10A/T&R | 功能描述:可編程振蕩器 RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS1073Z-10A+ | 功能描述:可編程振蕩器 RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
發布緊急采購，3分鐘左右您將得到回復。