參數資料
型號: DS1086U
英文描述: DS1086 Spread-Spectrum EconOscillator
中文描述: DS1086擴頻EconOscillator
文件頁數: 12/14頁
文件大?。?/td> 229K
代理商: DS1086U
D
DS1086 Spread-Spectrum EconOscillator
12
____________________________________________________________________
Since the expected output frequency is equal to the
desired frequency, the calculated error is 0%.
_______2-Wire Serial Port Operation
2-WIRE SERIAL DATA BUS
The DS1086 communicates through a 2-wire serial
interface. A device that sends data onto the bus is
defined as a transmitter, and a device receiving data
as a receiver. The device that controls the message is
called a "master." The devices that are controlled by the
master are "slaves." A master device that generates the
serial clock (SCL), controls the bus access, and gener-
ates the START and STOP conditions must control the
bus. The DS1086 operates as a slave on the 2-wire
bus. Connections to the bus are made through the
open-drain I/O lines SDA and SCL.
The following bus protocol has been defined (see
Figures 4 and 6):
Data transfer can be initiated only when the bus is
not busy.
During data transfer, the data line must remain
stable whenever the clock line is HIGH. Changes
in the data line while the clock line is high are
interpreted as control signals.
Accordingly, the following bus conditions have been
defined:
Bus not busy:
Both data and clock lines remain HIGH.
Start data transfer:
A change in the state of the data
line, from HIGH to LOW, while the clock is HIGH,
defines a START condition.
Stop data transfer:
A change in the state of the data
line, from LOW to HIGH, while the clock line is HIGH,
defines the STOP condition.
Data valid:
The state of the data line represents valid
data when, after a START condition, the data line is sta-
ble for the duration of the HIGH period of the clock sig-
nal. The data on the line must be changed during the
LOW period of the clock signal. There is one clock
pulse per bit of data.
SDA
SCL
t
HD:STA
t
LOW
t
HIGH
t
R
t
F
t
BUF
t
HD:DAT
t
SU:DAT
REPEATED
START
t
SU:STA
t
HD:STA
t
SU:STO
t
SP
STOP
START
Figure 6. 2-Wire AC Characteristics
MSB
DEVICE
IDENTIFIER
DEVICE
ADDRESS
RA/REI
1
0
1
1
A2
A1
A0
R/W
LSB
Figure 5. Slave Address
相關PDF資料
PDF描述
DS1086Z DS1086 Spread-Spectrum EconOscillator
DS1094L 10/100/1000 Base-T Ethernet LAN Switch
DS1094LU Multiphase Spread-Spectrum EconOscillator
DS1099 Low-Frequency Dual EconOscillator
DS1099U Space-Saving, 8-Channel Relay/Load Driver
相關代理商/技術參數
參數描述
DS1086U+ 功能描述:可編程振蕩器 5V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝:
DS1086U+T 功能描述:可編程振蕩器 5V SPRD OUTPUT OSC RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝:
DS1086U-266 功能描述:可編程振蕩器 5V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝:
DS1086U-266+ 功能描述:可編程振蕩器 5V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝:
DS1086Z 功能描述:可編程振蕩器 5V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: