- 您現在的位置：買賣IC網 > PDF目錄379184 > DS75S 2.Wire Thermal Watchdog PDF資料下載
參數資料
| 型號： | DS75S |
| 元件分類： | 溫度傳感器 |
| 英文描述： | 2.Wire Thermal Watchdog |
| 中文描述： | 2.Wire熱看門狗 |
| 文件頁數： | 3/13頁 |
| 文件大小： | 240K |
| 代理商： | DS75S |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁
DS75
3 of 13
DS75 FUNCTIONAL BLOCK DIAGRAM
Figure 1
OPERATION–Measuring Temperature
The core of DS75 functionality is its direct–to–digital temperature sensor. The DS75 measures
temperature through the use of an on–chip temperature measurement technique with an operating range
from –55
°
C to +125
°
C. Temperature conversions are initiated upon power–up, and the most recent result
is stored in the thermometer register. Conversions are performed continuously unless the user intervenes
by altering the configuration register to put the DS75 into a shutdown mode. Regardless of the mode
used, the digital temperature can be retrieved from the temperature register by setting the pointer to that
location (00h, power–up default). The DS75 power–up default has the sensor automatically performing
9–bit conversions continuously. Details on how to change the settings after pow-er up are contained in the
“OPERATION– Programming” section.
The resolution of the temperature conversion is configurable (9, 10, 11, or 12 bits), with 9–bit readings
the default state. This equates to a temperature resolution of 0.5
°
C, 0.25
°
C, 0.125
°
C, or 0.0625
°
C.
Following each conversion, thermal data is stored in the thermometer register in two’s complement
format; the information can be retrieved over the 2–wire interface with the device pointer set to the
temperature register. Table 2 describes the exact relationship of output data to measured temperature. The
table assumes the DS75 is configured for 12–bit resolution; if the device is configured in a lower
resolution mode, those bits will contain zeros. The data is transmitted serially over the 2–wire serial
interface, MSb first. The MSb of the temperature register contains the “sign” (S) bit, denoting whether the
temperature is positive or negative. For Fahrenheit usage, a lookup table or conversion routine must be
used.
相關PDF資料 |
PDF描述 |
|---|---|
| DS80CH11 | System Energy Manager |
| DS83C520 | EPROM/ROM High-Speed Micro |
| DS83C520-ECL | EPROM/ROM High-Speed Micro |
| DS83C520-ENL | EPROM/ROM High-Speed Micro |
| DS83C520-MCL | EPROM/ROM High-Speed Micro |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS75S/T&R | 制造商:Maxim Integrated Products 功能描述:2-WIRE THERMAL WATCHDOG SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC WATCHDOG THERM 2-W 3/5V 8SOIC |
| DS75S/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS75S+ | 功能描述:板上安裝溫度傳感器 Digital RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS75S+/ | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS75S+T&R | 制造商:Maxim Integrated Products 功能描述:DS75 LEAD FREE SO 8 T&R 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 2-WIRE 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8-SOIC 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Digital 制造商:Maxim Integrated Products 功能描述:Temp Sensor Digital Serial (2-Wire) SO8 |
發布緊急采購，3分鐘左右您將得到回復。