- 您現在的位置：買賣IC網 > PDF目錄379184 > DS75S 2.Wire Thermal Watchdog PDF資料下載
參數資料
| 型號： | DS75S |
| 元件分類： | 溫度傳感器 |
| 英文描述： | 2.Wire Thermal Watchdog |
| 中文描述： | 2.Wire熱看門狗 |
| 文件頁數： | 5/13頁 |
| 文件大?。?/td> | 240K |
| 代理商： | DS75S |
DS75
5 of 13
O.S. OUTPUT TRANSFER FUNCTION
Figure 2
Regardless of the mode chosen, the O.S. output is open–drain and the active state is set in the configura-
tion register. The power–up default is active low. Refer to the “OPERATION–Programming” section for
instructions in adjusting the thermostat setpoints, thermostat mode, and O.S. active state.
OPERATION–Programming
There are three areas of interest in programming the DS75: Configuration register, T
OS
register, and the
T
HYST
register. All programming is done via the 2–wire interface by setting the pointer to the appropriate
location. Table 3 illustrates the pointer settings for the four registers of the DS75.
Pointer Register Structure Table 3
POINTER
ACTIVE REGISTER
00h
Temperature (default)
01h
Configuration
02h
03h
T
HYST
T
OS
The DS75 will power up with the temperature register selected. If the host wishes to change the data
pointer, it simply addresses the DS75 in the write mode (R/W=0), receives an acknowledge, and writes
the 8 bits that correspond to the new desired location. The last pointer location is always maintained so
that consecutive reads from the same register do not require the host to always provide a pointer address.
The only exception is at power–up, in which case the pointer will always be set to 00h, the temperature
register. The pointer address must always proceed data in writing to a register, regardless of which
address is currently selected. Please refer to the “2–Wire Serial Data Bus” section for details of the 2–
wire bus protocol.
相關PDF資料 |
PDF描述 |
|---|---|
| DS80CH11 | System Energy Manager |
| DS83C520 | EPROM/ROM High-Speed Micro |
| DS83C520-ECL | EPROM/ROM High-Speed Micro |
| DS83C520-ENL | EPROM/ROM High-Speed Micro |
| DS83C520-MCL | EPROM/ROM High-Speed Micro |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS75S/T&R | 制造商:Maxim Integrated Products 功能描述:2-WIRE THERMAL WATCHDOG SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC WATCHDOG THERM 2-W 3/5V 8SOIC |
| DS75S/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS75S+ | 功能描述:板上安裝溫度傳感器 Digital RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS75S+/ | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS75S+T&R | 制造商:Maxim Integrated Products 功能描述:DS75 LEAD FREE SO 8 T&R 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 2-WIRE 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8-SOIC 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Digital 制造商:Maxim Integrated Products 功能描述:Temp Sensor Digital Serial (2-Wire) SO8 |
發布緊急采購，3分鐘左右您將得到回復。