參數資料
型號： DS80CH11
英文描述： System Energy Manager
中文描述： 系統能量管理器
文件頁數： 52/88頁
文件大?。?/td> 598K
代理商： DS80CH11
DS80CH11
011200 52/88
8.0
ACTIVITY MONITOR/LED CONTROL
8.1
During periods of inactivity, varying levels of standby
and suspend modes of operation can be initiated by the
SEM. Inactivity can be detected by the SEM and then
action can be taken to reduce the power consumption of
the system and thereby conserve operating power.
OVERVIEW
Activity monitoring is performed by the special logic pro-
vided as an alternate function on all lines of Port 7. This
alternate function allows any combination of the Port 7
pins to be configured as activity monitor inputs. In this
mode, these pins are intended for connection to the chip
select signals of external peripheral subsystems, such
as the hard disk, floppy, etc. These pins can be option-
ally qualified by the IOR and IOW input control signals.
When inactivity is detected, peripheral devices such as
the LCD display, hard disk, floppy disk, and modem are
turned off as required by the microcontroller firmware.
This is accomplished via parallel I/O pins as assigned by
the user. When CPU accesses to memory or I/O loca-
tions which are connected to the activity monitor inputs
are detected, accessed peripheral devices can be
turned back on by the firmware. As an option, the host
CPU can be notified of the power on sequence by writ-
ing a word to a power management host interface port,
which activates either SMI1 or SMI2.
8.2
OPERATION
The activity monitor enable bits in the Activity Monitor
Enable (AME–092H) register select the associated pins
from Port 7 as activity monitor inputs. In order to func-
tion properly, each enabled pin must have a 1 pro-
grammed into its Port 7 output latch bit. The current
state of the Port 7 pins can always be read through the
Port 7 input buffer regardless of the programming of the
activity monitor enable bits. Figure 8–1 shows the logic
associated with each Activity Monitor Input.
ACTIVITY MONITOR INPUT
The active state for each pin is programmed via the
Activity Monitor Polarity register (AMP–094H). A “0”
programmed into a bit in the AMP register selects a low
state signal as active for the pin (default case) while a “1”
selects a high state signal.
When an active state is detected on an enabled activity
monitor pin, the associated bit in the Activity Monitor
Flag (AMF–095H) will be set.
In order to avoid false triggering of the activity monitor
inputs due to glitches from an external address decoder,
the inputs can be optionally qualified by the IOR and
IOW lines via the Activity Monitor Qualify register
(AMQ–093H). When a bit is set to 1 in the AMQ register,
the associated pin will not be active unless it is accom-
panied by a valid IOR or IOW signal. When AMQ bits
are 0, the associated pins qualify function is disabled
(default case).
Interrupts initiated from the enabled activity monitor pins
are enabled by the EAM bit (IE.6), and their priority can
be adjusted via PAM (IP.6). When activity monitor inter-
rupts are enabled and an active state occurs, an inter-
rupt will be generated, and the SEM firmware should
read the AMF register to determine the source of the
interrupt. The interrupt flag can be cleared by writing a
“0” to the flag bit; writing a 1 will have no effect.
When all peripheral devices in the system are fully pow-
ered, host accesses to them may occur very often. So
often in fact, that if these accesses were to initiate inter-
rupts during this time the SEM may be bogged down in
unnecessary interrupt service routines servicing the
interrupts. Typically, it is necessary only to ascertain
whether each monitored device has been accessed by
the host over the past, say, 16–second period. In order
to eliminate any unnecessary interrupt processing bur-
den, it may be desirable to disable the interrupts from
the activity monitor inputs (e.g., by clearing EAM) and
reading the register once during each such period. This
period can be easily set up via the Power Down Periodic
Interrupt described below.
相關PDF資料
PDF描述
DS83C520 EPROM/ROM High-Speed Micro
DS83C520-ECL EPROM/ROM High-Speed Micro
DS83C520-ENL EPROM/ROM High-Speed Micro
DS83C520-MCL EPROM/ROM High-Speed Micro
DS83C520-MNL EPROM/ROM High-Speed Micro
相關代理商/技術參數
參數描述
DS80CH11+E02 制造商:Maxim from Components Direct 功能描述:MAXIM DS80CH11+E02 SYSTEM ENERGY MANAGERS - Trays 制造商:Maxim 功能描述:Maxim DS80CH11+E02 System Energy Managers
DS80CH11-E02 制造商:Maxim from Components Direct 功能描述:MAXIM DS80CH11-E02 SYSTEM ENERGY MANAGERS - Trays 制造商:Maxim 功能描述:Maxim DS80CH11-E02 System Energy Managers
DS80E100 制造商:NSC 制造商全稱:National Semiconductor 功能描述:5 to 12.5 Gbps, Power-Saver Equalizer for Backplanes and Cables
DS80EP100 制造商:NSC 制造商全稱:National Semiconductor 功能描述:5 to 12.5 Gbps, Power-Saver Equalizer for Backplanes and Cables
DS80EP100_08 制造商:NSC 制造商全稱:National Semiconductor 功能描述:5 to 12.5 Gbps, Power-Saver Equalizer for Backplanes and Cables
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*