參數資料
型號： DS87C520-ECL
英文描述： EPROM/ROM High-Speed Micro
中文描述： 存儲器/ ROM的高速微
文件頁數： 17/45頁
文件大?。?/td> 1415K
代理商： DS87C520-ECL
DS87C520/DS83C520 EPROM/ROM High-Speed Microcontrollers
17 of 45
Crystal/Ring Operation
The DS87C520/DS83C520 allow software to choose the clock source as an independent selection from
the instruction cycle rate. The user can select crystal-based or ring oscillator-based operation under
software control. Power-on reset default is the crystal (or external clock) source. The ring may save
power depending on the actual crystal speed. To save still more power, software can then disable the
crystal amplifier. This process requires two steps. Reversing the process also requires two steps.
The XT/
RG
bit (EXIF.3) selects the crystal or ring as the clock source. Setting XT/
RG
= 1 selects the
crystal. Setting XT/
RG
= 0 selects the ring. The RGMD (EXIF.2) bit serves as a status bit by indicating
the active clock source. RGMD = 0 indicates the CPU is running from the crystal. RGMD = 1 indicates it
is running from the ring. When operating from the ring, disable the crystal amplifier by setting the
XTOFF bit (PMR.3) to 1. This can only be done when XT/
RG
= 0.
When changing the clock source, the selection will take effect after a one-instruction cycle delay. This
applies to changes from crystal to ring and vise versa. However, this assumes that the crystal amplifier is
running. In most cases, when the ring is active, software previously disabled the crystal to save power. If
ring operation is being used and the system must switch to crystal operation, the crystal must first be
enabled. Set the XTOFF bit to 0. At this time, the crystal oscillation will begin. The
DS87C520/DS83C520 then provide a warm-up delay to make certain that the frequency is stable.
Hardware will set the XTUP bit (STATUS.4) to a 1 when the crystal is ready for use. Then software
should write XT/
RG
to 1 to begin operating from the crystal. Hardware prevents writing XT/
RG
to 1
before XTUP=1. The delay between XTOFF = 0 and XTUP = 1 will be 65,536 crystal clocks in addition
to the crystal cycle startup time.
Switchback has no effect on the clock source. If software selects a reduced clock divider and enables the
ring, a Switchback will only restore the divider speed. The ring will remain as the time base until altered
by software. If there is serial activity, Switchback usually occurs with enough time to create proper baud
rates. This is not true if the crystal is off and the CPU is running from the ring. If sending a serial
character that wakes the system from crystal-less PMM, then it should be a dummy character of no
importance with a subsequent delay for crystal startup.
Figure 3 illustrates a typical decision set associated with PMM. Table 6 is a summary of the bits relating
to PMM and its operation.
相關PDF資料
PDF描述
DS87C520-ENL EPROM/ROM High-Speed Micro
DS87C520-MCL EPROM/ROM High-Speed Micro
DS87C520-MNL EPROM/ROM High-Speed Micro
DS87C520-QCL EPROM/ROM High-Speed Micro
DS87C520-QNL EPROM/ROM High-Speed Micro
相關代理商/技術參數
參數描述
DS87C520-ECL+ 功能描述:8位微控制器 -MCU EPROM/ROM High-Speed RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS87C520-ENL 功能描述:8位微控制器 -MCU EPROM/ROM High-Speed RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS87C520-ENL+ 功能描述:8位微控制器 -MCU EPROM/ROM High-Speed RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS87C520-FCL 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
DS87C520MCL 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:EPROM/ROM High-Speed Microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*