- 您現在的位置：買賣IC網 > PDF目錄379184 > DS87C520 EPROM/ROM High-Speed Micro PDF資料下載
參數資料
| 型號： | DS87C520 |
| 英文描述： | EPROM/ROM High-Speed Micro |
| 中文描述： | EPROM/ROM高速微控制器 |
| 文件頁數： | 17/45頁 |
| 文件大小： | 1415K |
| 代理商： | DS87C520 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
DS87C520/DS83C520 EPROM/ROM High-Speed Microcontrollers
17 of 45
Crystal/Ring Operation
The DS87C520/DS83C520 allow software to choose the clock source as an independent selection from
the instruction cycle rate. The user can select crystal-based or ring oscillator-based operation under
software control. Power-on reset default is the crystal (or external clock) source. The ring may save
power depending on the actual crystal speed. To save still more power, software can then disable the
crystal amplifier. This process requires two steps. Reversing the process also requires two steps.
The XT/
RG
bit (EXIF.3) selects the crystal or ring as the clock source. Setting XT/
RG
= 1 selects the
crystal. Setting XT/
RG
= 0 selects the ring. The RGMD (EXIF.2) bit serves as a status bit by indicating
the active clock source. RGMD = 0 indicates the CPU is running from the crystal. RGMD = 1 indicates it
is running from the ring. When operating from the ring, disable the crystal amplifier by setting the
XTOFF bit (PMR.3) to 1. This can only be done when XT/
RG
= 0.
When changing the clock source, the selection will take effect after a one-instruction cycle delay. This
applies to changes from crystal to ring and vise versa. However, this assumes that the crystal amplifier is
running. In most cases, when the ring is active, software previously disabled the crystal to save power. If
ring operation is being used and the system must switch to crystal operation, the crystal must first be
enabled. Set the XTOFF bit to 0. At this time, the crystal oscillation will begin. The
DS87C520/DS83C520 then provide a warm-up delay to make certain that the frequency is stable.
Hardware will set the XTUP bit (STATUS.4) to a 1 when the crystal is ready for use. Then software
should write XT/
RG
to 1 to begin operating from the crystal. Hardware prevents writing XT/
RG
to 1
before XTUP=1. The delay between XTOFF = 0 and XTUP = 1 will be 65,536 crystal clocks in addition
to the crystal cycle startup time.
Switchback has no effect on the clock source. If software selects a reduced clock divider and enables the
ring, a Switchback will only restore the divider speed. The ring will remain as the time base until altered
by software. If there is serial activity, Switchback usually occurs with enough time to create proper baud
rates. This is not true if the crystal is off and the CPU is running from the ring. If sending a serial
character that wakes the system from crystal-less PMM, then it should be a dummy character of no
importance with a subsequent delay for crystal startup.
Figure 3 illustrates a typical decision set associated with PMM. Table 6 is a summary of the bits relating
to PMM and its operation.
相關PDF資料 |
PDF描述 |
|---|---|
| DS87C520-ECL | EPROM/ROM High-Speed Micro |
| DS87C520-ENL | EPROM/ROM High-Speed Micro |
| DS87C520-MCL | EPROM/ROM High-Speed Micro |
| DS87C520-MNL | EPROM/ROM High-Speed Micro |
| DS87C520-QCL | EPROM/ROM High-Speed Micro |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS87C520_1 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:EPROM/ROM High-Speed Micro |
| DS87C520+ECL | 制造商:Maxim Integrated Products 功能描述:MICRO OTP HI SPD 44TQFP 33MHZ PB-FR - Trays |
| DS87C520+MCL | 制造商:Maxim Integrated Products 功能描述:MICRO OTP HI SPD 40PDIP 33MHZ PB-FR - Rail/Tube 制造商:Maxim Integrated Products 功能描述:IC 8BIT CPU CMOS 87C520 DIP40 |
| DS87C520+MNL | 制造商:Maxim Integrated Products 功能描述:MICRO HI SPD 40PDIP 33MHZ IND PB-FR - Rail/Tube |
| DS87C520+QCL | 制造商:Maxim Integrated Products 功能描述:MCU 8BIT CISC 16KB EPROM 5V 44PLCC - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。