參數資料
型號： DS2180AN
廠商： Maxim Integrated Products
文件頁數： 14/35頁
文件大?。?/td> 0K
描述： IC TRANSCEIVER T1 IND 40-DIP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 10
功能： 收發器
接口： T1
電路數： 1
電源電壓： 4.5 V ~ 5.5 V
電流 - 電源： 3mA
工作溫度： -40°C ~ 85°C
安裝類型： 通孔
封裝/外殼： 40-DIP（0.600"，15.24mm）
供應商設備封裝： 40-PDIP
包裝： 管件
包括： 警報生成和檢測，B7 填充模式，B8ZS 模式，錯誤檢測和計數器，“硬件”模式，透明模式
DS2180A
21 of 35
RYEL OUTPUT
The yellow alarm output transitions high when a yellow alarm is detected. A high-low transition indicates
the alarm condition has been cleared. The RYEL bit (RSR.5) is a “l(fā)atched” version of the RYEL output.
In 193E framing, the yellow alarm pattern detected is 16 pattern sets of 00 (Hex) and FF (Hex) received
at RLINK. In 193S, framing the yellow alarm format is de-pendent on CCR.3; if CCR.3=0, the RYEL
output transitions high if bit 2 of 256 or more consecutive channels is 0; if CCR.3=1, yellow alarm is
declared when the S-bit received in frame 12 is 1.
RBV OUTPUT
The bipolar violation output transitions high when an accused bit emerges at RSER. RBV will go low at
the next bit time if no additional violations are detected.
RFER OUTPUT
The receive frame error output transitions high at the F-bit time and is held high for two bit periods when
a frame bit error occurs. In 193S framing, FT and FS patterns are tested. The FPS pattern is tested in 193E
framing. Additionally, in 193E framing, RFER reports a CRC error by a low-high-low transition (one bit
period wide) one half RCLK period before a low-high transition on RMSYNC.
RESET
A high-low transition on RST clears all registers and forces immediate receive resync when RST returns
high. This reset has no effect on transmit frame multiframe or channel counters. RST must be held low on
system power-up to insure proper initialization of transceiver counters and registers. Following reset, the
host processor should restore all control modes by writing appropriate registers with control data.
ALARM OUTPUT TIMING Figure 21
NOTES:
1. RFER transitions high during F-bit time if received framing pattern bit is in error. (Frame 12 F-bits in
193S are ignored if CCR.3=1). Also, in 193E, RFER transitions 1/2 bit time before the rising edge of
RMSYNC to indicate a CRC error for the previous multiframe.
2. RBV indicates received bipolar violation and transitions high when an accused bit emerges from
RSER. If B8ZS is enabled, RBV will not report the zero replacement code.
3. RCL transitions high (during 32nd bit time) when 32 consecutive bits received are 0; RCL transitions
low when the next 1 is received.
相關PDF資料
PDF描述
DS2180AQ/T&R IC TRANSCEIVER T1 44-PLCC
DS2180AQ+T&R IC TRANSCEIVER T1 44-PLCC
VI-2VY-IX-F4 CONVERTER MOD DC/DC 3.3V 49.5W
DS2172T+T&R IC TESTER BIT ERROR RATE 32-TQFP
VI-2VY-IX-F3 CONVERTER MOD DC/DC 3.3V 49.5W
相關代理商/技術參數
參數描述
DS2180AQ 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2180AQ/T&R 制造商:Maxim Integrated Products 功能描述:T1 TRANSCEIVER-PLCC-TRL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TRANSCEIVER T1 44-PLCC 制造商:Maxim Integrated Products 功能描述:Network Controller & Processor ICs T1 Transceiver
DS2180AQ/T&R+ 制造商:Maxim Integrated Products 功能描述:T1 TRANSCEIVER PLCC TRL LF - Tape and Reel
DS2180AQ/T&R 功能描述:網絡控制器與處理器 IC T1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2180AQ+ 功能描述:網絡控制器與處理器 IC T1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*