- 您現在的位置：買賣IC網 > PDF目錄353101 > EL2044CSZT13 (Intersil Corporation) Low Power/Low Voltage 120MHz Unity-Gain Stable Operational Amplifier PDF資料下載
參數資料
| 型號： | EL2044CSZT13 |
| 廠商： | Intersil Corporation |
| 英文描述： | Low Power/Low Voltage 120MHz Unity-Gain Stable Operational Amplifier |
| 中文描述： | 低功耗/低電壓120MHz的單位增益穩定運算放大器 |
| 文件頁數： | 13/13頁 |
| 文件大?。?/td> | 414K |
| 代理商： | EL2044CSZT13 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁
9
EL2044C
Low Power/Low Voltage 120MHz Unity-Gain Stable Operational Amplifier
E
L
20
44
C
Applications Information
Product Description
The EL2044C is a low-power wideband monolithic
operational amplifier built on Elantec's proprietary high-
speed complementary bipolar process. The EL2044C
uses a classical voltage-feedback topology which allows
it to be used in a variety of applications where current-
feedback amplifiers are not appropriate because of
restrictions placed upon the feedback element used with
the amplifier. The conventional topology of the
EL2044C allows, for example, a capacitor to be placed
in the feedback path, making it an excellent choice for
applications such as active filters, sample-and-holds, or
integrators. Similarly, because of the ability to use
diodes in the feedback network, the EL2044C is an
excellent choice for applications such as fast log
amplifiers.
Single-Supply Operation
The EL2044C has been designed to have a wide input
and output voltage range. This design also makes the
EL2044C an excellent choice for single-supply opera-
tion. Using a single positive supply, the lower input
voltage range is within 100mV of ground (RL = 500),
and the lower output voltage range is within 300mV of
ground. Upper input voltage range reaches 4.2V, and
output voltage range reaches 3.8V with a 5V supply and
RL = 500. This results in a 3.5V output swing on a sin-
gle 5V supply. This wide output voltage range also
allows single-supply operation with a supply voltage as
high as 36V or as low as 2.5V. On a single 2.5V supply,
the EL2044C still has 1V of output swing.
Gain-Bandwidth Product and the -3dB
Bandwidth
The EL2044C has a gain-bandwidth product of 60MHz
while using only 5.2mA of supply current. For gains
greater than 4, its closed-loop -3dB bandwidth is
approximately equal to the gain-bandwidth product
divided by the noise gain of the circuit. For gains less
than 4, higher-order poles in the amplifier's transfer
function contribute to even higher closed loop band-
widths. For example, the EL2044C has a -3dB
bandwidth of 120MHz at a gain of +1, dropping to
60MHz at a gain of +2. It is important to note that the
EL2044C has been designed so that this “extra” band-
width in low-gain applications does not come at the
expense of stability. As seen in the typical performance
curves, the EL2044C in a gain of +1 only exhibits 1.0dB
of peaking with a 1000
load.
Video Performance
An industry-standard method of measuring the video
distortion of a component such as the EL2044C is to
measure the amount of differential gain (dG) and differ-
ential phase (dP) that it introduces. To make these
measurements, a 0.286VPP (40 IRE) signal is applied to
the device with 0V DC offset (0 IRE) at either 3.58MHz
for NTSC or 4.43MHz for PAL. A second measurement
is then made at 0.714V DC offset (100 IRE). Differential
gain is a measure of the change in amplitude of the sine
wave, and is measured in percent. Differential phase is a
measure of the change in phase, and is measured in
degrees.
For signal transmission and distribution, a back-termi-
nated cable (75
in series at the drive end, and 75 to
ground at the receiving end) is preferred since the
impedance match at both ends will absorb any reflec-
tions. However, when double termination is used, the
received signal is halved; therefore a gain of 2 configu-
ration is typically used to compensate for the
attenuation.
The EL2044C has been designed as an economical solu-
tion for applications requiring low video distortion. It
has been thoroughly characterized for video perfor-
mance in the topology described above, and the results
have been included as typical dG and dP specifications
and as typical performance curves. In a gain of +2, driv-
ing 150, with standard video test levels at the input, the
EL2044C exhibits dG and dP of only 0.04% and 0.15° at
NTSC and PAL. Because dG and dP can vary with dif-
ferent DC offsets, the video performance of the
EL2044C has been characterized over the entire DC off-
set range from -0.714V to +0.714V. For more
information, refer to the curves of dG and dP vs DC
Input Offset.
相關PDF資料 |
PDF描述 |
|---|---|
| EL2270CSZT13 | 70MHz/1mA Current Mode Feedback Amplifiers |
| EL2386CSZT13 | 250MHz Triple Current Feedback Amplifier with Disable |
| EL5227CR-T13 | CSN Series closed loop current sensor, measures ac, dc or impulse current, 100 A nominal, ± 150 amp range, offset pin, 2000 turn |
| EL5227CR-T7 | 2.5MHz 4, 8, 10 & 12 Channel Rail-to-Rail Buffers |
| EL5197CW-T7 | Single 200MHz Fixed Gain Amplifier with Enable |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EL2044CSZ-T7 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power/Low Voltage 120MHz Unity-Gain Stable Operational Amplifier |
| EL2045 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low-Power 100MHz Gain-of-2 Stable Operational Amplifier |
| EL2045C | 制造商:ELANTEC 制造商全稱:ELANTEC 功能描述:Low-Power 100 MHz Gain-of-2 Stable Operational Amplifier |
| EL2045CN | 功能描述:IC OP AMP 100MHZ HS 8-PDIP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| EL2045CNP | 制造商:Intersil Corporation 功能描述:2045CNP |
發布緊急采購，3分鐘左右您將得到回復。