- 您現在的位置：買賣IC網 > PDF目錄362737 > EP1C6T256C6 (Altera Corporation) Cyclone FPGA Family PDF資料下載
參數資料
| 型號： | EP1C6T256C6 |
| 廠商： | Altera Corporation |
| 英文描述： | Cyclone FPGA Family |
| 中文描述： | 氣旋FPGA系列 |
| 文件頁數： | 66/94頁 |
| 文件大?。?/td> | 1138K |
| 代理商： | EP1C6T256C6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁當前第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
66
Altera Corporation
Cyclone FPGA Family Data Sheet
Preliminary Information
Operating Modes
The Cyclone architecture uses SRAM configuration elements that require
configuration data to be loaded each time the circuit powers up. The
process of physically loading the SRAM data into the device is called
configuration. During initialization, which occurs immediately after
configuration, the device resets registers, enables I/O pins, and begins to
operate as a logic device. Together, the configuration and initialization
processes are called command mode. Normal device operation is called
user mode.
SRAM configuration elements allow Cyclone devices to be reconfigured
in-circuit by loading new configuration data into the device. With real-
time reconfiguration, the device is forced into command mode with a
device pin. The configuration process loads different configuration data,
reinitializes the device, and resumes user-mode operation. Designers can
perform in-field upgrades by distributing new configuration files either
within the system or remotely.
A built-in weak pull-up resistor pulls all user I/O pins to V
CCIO
before
and during device configuration.
The configuration pins support 1.5-V/1.8-V or 2.5-V/3.3-V I/O standards.
The voltage level of the configuration output pins is determined by the
V
CCIO
of the bank where the pins reside. The bank V
CCIO
selects whether
the configuration inputs are 1.5-V, 1.8-V, 2.5-V, or 3.3-V compatible.
Configuration Schemes
Designers can load the configuration data for a Cyclone device with one
of three configuration schemes (see
Table 22
), chosen on the basis of the
target application. Designers can use a configuration device, intelligent
controller, or the JTAG port to configure a Cyclone device. A low-cost
configuration device can automatically configure a Cyclone device at
system power-up.
相關PDF資料 |
PDF描述 |
|---|---|
| EP1C6T256C7 | Cyclone FPGA Family |
| EP1C6T256C8 | Cyclone FPGA Family |
| EP1C6T256I6 | Cyclone FPGA Family |
| EP1C6T256I7 | Cyclone FPGA Family |
| EP1C6T256I8 | Cyclone FPGA Family |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EP1F | 制造商:NEC 制造商全稱:NEC 功能描述:HIGH HEAT RESISTIVITY |
| EP1F-B3G1 | 制造商:NEC 制造商全稱:NEC 功能描述:HIGH HEAT RESISTIVITY |
| EP1FB3G1S | 制造商:World Products 功能描述:Electromechanical Relay SPDT 25A 12VDC 225Ohm Through Hole |
| EP1F-B3G1T | 制造商:NEC 制造商全稱:NEC 功能描述:HIGH HEAT RESISTIVITY |
| EP1F-B3G1TT | 制造商:NEC 制造商全稱:NEC 功能描述:HIGH HEAT RESISTIVITY |
發布緊急采購，3分鐘左右您將得到回復。