參數資料
型號: EP1K100
廠商: Electronic Theatre Controls, Inc.
英文描述: Programmable Logic Device Family
中文描述: 可編程邏輯器件系列
文件頁數: 41/86頁
文件大?。?/td> 992K
代理商: EP1K100
Altera Corporation
41
ACEX 1K Programmable Logic Device Family Data Sheet
D
13
T
The
VCCINT
pins must always be connected to a 2.5-V power supply. With
a 2.5-V V
CCINT
level, input voltages are compatible with 2.5-V, 3.3-V, and
5.0-V inputs. The
VCCIO
pins can be connected to either a 2.5-V or 3.3-V
power supply, depending on the output requirements. When the
VCCIO
pins are connected to a 2.5-V power supply, the output levels are
compatible with 2.5-V systems. When the
VCCIO
pins are connected to a
3.3-V power supply, the output high is at 3.3 V and is therefore compatible
with 3.3-V or 5.0-V systems. Devices operating with V
CCIO
levels higher
than 3.0 V achieve a faster timing delay of
t
OD2
instead of
t
OD1
.
Table 13
summarizes ACEX 1K MultiVolt I/ O support.
Notes:
(1)
The PCI clamping diode must be disabled on an input which is driven with a
voltage higher than V
CCIO
.
When V
CCIO
= 3.3 V, an ACEX 1K device can drive a 2.5-V device that has 3.3-V
tolerant inputs.
(2)
Open-drain output pins on ACEX 1K devices (with a pull-up resistor to
the 5.0-V supply) can drive 5.0-V CMOS input pins that require a higher
V
IH
than LVTTL. When the open-drain pin is active, it will drive low.
When the pin is inactive, the resistor will pull up the trace to 5.0 V, thereby
meeting the CMOS V
OH
requirement. The open-drain pin will only drive
low or tri-state; it will never drive high. The rise time is dependent on the
value of the pull-up resistor and load impedance. The I
OL
current
specification should be considered when selecting a pull-up resistor.
Power
Sequencing &
Hot-Socketing
Because ACEX 1K devices can be used in a mixed-voltage environment,
they have been designed specifically to tolerate any possible power-up
sequence. The V
CCIO
and V
CCINT
power planes can be powered in any
order.
Signals can be driven into ACEX 1K devices before and during power up
without damaging the device. Additionally, ACEX 1K devices do not
drive out during power up. Once operating conditions are reached,
ACEX 1K devices operate as specified by the user.
Table 13. ACEX 1K MultiVolt I/O Support
V
CCIO
(V)
Input Signal (V)
Output Signal (V)
2.5
3.3
5.0
v
(1)
v
(1)
2.5
3.3
5.0
2.5
v
v
v
(1)
v
v
3.3
v
(2)
v
v
相關PDF資料
PDF描述
EP1K30 Programmable Logic Device Family
EP1K50 Programmable Logic Device Family
EP1S60B1508C5ES Stratix Device Family Data Sheet
EP1S10B1508C6ES Stratix Device Family Data Sheet
EP1S80F1508I5ES Stratix Device Family Data Sheet
相關代理商/技術參數
參數描述
EP1K100FC256-1 功能描述:FPGA - 現場可編程門陣列 FPGA - ACEX 1K 624 LABs 186 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
EP1K100FC256-1N 功能描述:FPGA - 現場可編程門陣列 FPGA - ACEX 1K 624 LABs 186 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
EP1K100FC256-2 功能描述:FPGA - 現場可編程門陣列 FPGA - ACEX 1K 624 LABs 186 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
EP1K100FC256-2N 功能描述:FPGA - 現場可編程門陣列 FPGA - ACEX 1K 624 LABs 186 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
EP1K100FC2563 制造商:Altera Corporation 功能描述: