參數資料
型號: EP7211
廠商: Cirrus Logic, Inc.
英文描述: HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER
中文描述: 高性能超低功耗系統與LCD控制器芯片
文件頁數: 124/166頁
文件大小: 2623K
代理商: EP7211
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁當前第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁
EP7211
High-Performance Ultra-Low-Power System-on-Chip with LCD Controller
124
Register Descriptions
DS352PP3
JUL 2001
5.16.2.3
MCP Data Register 2
ADDRESS: 0x8000.20C0
MCDR2 contains 21 bits and is used to perform reads and writes to any of the UCB1100
s sixteen
registers. MCDR2 contains three separate fields: MCDR2[15:0] is the 16-bit register data field,
MCDR2[16] is a 1-bit read/write control bit, and MCDR2[20:17] is the 4-bit register address field.
A value written to MCDR2 is placed in the correct position within the 64-bit subframe 0, is
transmitted to the off-chip codec, and is used to perform a read or write operation to the addressed
codec register. Note that the contents of the addressed register are always returned in the receive data
frame and placed in the MCDR2 registers regardless of the state of the read/write bit. Thus, for write
cycles, both a write and a read occurs, and for read cycles, only a read occurs. When MCDR2 is read,
the value returned from the last read or write operation which was completed to the codec is returned.
A register write is performed by writing the correct value to each of the three fields within MCDR2
using one 16- or 32-bit write, ensuring that the read/write bit is set. Its contents are then transferred
to the correct fields within the serial shifter on the next rising-edge of the
SIBSYNC
signal, and then
to the codec via the
SIBDOUT
pin during subframe 0. The value within MCDR2[15:0] is written to
the selected codec register at the end of subframe 0 (during the 65th bit of the frame). The data
written to the control register and its address are returned to the MCP during the next data frame, and
are placed back within MCDR2, with the read/write bit reset to zero. For a write operation, since the
addressed register is written at the end of subframe 0, the data returned during the frame in which the
write occurred represents the previous contents of the register. The updated value is returned during
the next data frame.
A register read is performed by writing the address of the register to read while clearing the
read/write bit to zero within MCDR2. Again, the data is transferred to the serial shifter on the next
rising-edge of the
SIBSYNC
signal and is transmitted to the UCB1100 during subframe 0. Because
the address and read/write control bit fields are placed near the beginning of the serial stream output,
the codec performs the read immediately after the read/write bit is received (during the 41st bit of
the frame) and the value contained within the addressed register is sent back to the MCP in the same
data frame, and is placed within MCDR2.
Once MCDR2 is written with a value to execute a read or write, the operation is performed every
MCP data frame until a new value is written to the register. Thus continuous reads or writes are made
to the addressed codec register until a new read or write operation is configured.
The following figure shows the location of MCP data register 2. Note that the reset state of all
MCDR2 bits is unknown, writes to reserved bits are ignored and reads return zeros.
相關PDF資料
PDF描述
EP7211-CP-A HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER
EP7211-CV-A HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER
EP7212 HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
EP7212-CB-A HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
EP7212-CV-A HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
相關代理商/技術參數
參數描述
EP7211(208LQFP) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Logic IC
EP7211(256PBGA) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Logic IC
EP7211-CB-D 制造商:Rochester Electronics LLC 功能描述:- Bulk
EP7211-CP-A 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER
EP7211-CV-A 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER