參數資料
型號： EP7212
廠商： Cirrus Logic, Inc.
英文描述： HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
中文描述： 高性能，低功耗系統與LCD控制器和數字音頻接口（DAI芯片）
文件頁數： 23/136頁
文件大?。?/td> 2289K
代理商： EP7212
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁
EP7212
DS474PP1
23
2) Ensure that on entry to the Standby State, the
chosen interrupt source is not masked, and the
UART is enabled.
3) Send a preamble that consists of one start bit,
8 bits of zero, and one stop bit. This will cause
the EP7212 to wake and execute the enabled in-
terrupt vector.
The UART will automatically be re-enabled when
the processor re-enters the Operating State, and the
preamble will be received. Since the UART was
not awake at the start of the preamble, the timing of
the sample point will be off-center during the pre-
amble byte. However, the next byte transmitted
will be correctly aligned. Thus, the actual first real
byte to be received by the UART will get captured
correctly.
3.2.2
Idle State
If in the Operating State, the Idle State can be en-
tered by writing to a special internal memory loca-
tion (HALT) in the EP7212. If an interrupt occurs,
the EP7212 will return immediately back to the Op-
erating State and execute the next instruction. The
WAKEUP signal can not be used to exit the Idle
State. It is only used to exit the Standby State.
In the Idle State, the device functions just like it
does when in the Operating State. However, the
CPU clock is halted while it waits for an event such
as a key press to generate an interrupt. The PLL (in
18.432–73.728 MHz mode) or the external
13 MHz clock source always remains active in the
Idle State.
3.2.3
Keyboard Interrupt
For the case of the keyboard interrupt, the follow-
ing options are available and are selectable accord-
ing to bits 1 and 3 of the SYSCON2 register (refer
to the
SYSCON2 Register Description
for details).
If the KBWEN bit (SYSCON2 bit 3) is set low,
then a keypress will cause a transition from a
power saving state only if the keyboard inter-
rupt is non-masked (i.e., the interrupt mask reg-
ister 2 (INTMR2 bit 0) is high).
When KBWEN is high, a keypress will cause
the device to wake up regardless of the state of
the interrupt mask register. This is called the
“Keyboard Direct Wakeup’ mode. In this
mode, the interrupt request may not get ser-
viced. If the interrupt is masked (i.e., the inter-
rupt mask register 2 (INTMR2 bit 0) is low),
the processor simply starts re-executing code
from where it left off before it entered the pow-
er saving state. If the interrupt is non-masked,
then the processor will service the interrupt.
When the KBD6 bit (SYSCON2 bit 1) is low,
all 8 of Port A inputs are OR’ed together to pro-
duce the internal wakeup signal and keyboard
interrupt request. This is the default reset state.
When the KBD6 bit (SYSCON2 bit 1) is high,
only the lowest 6 bits of Port A are OR’ed to-
gether to produce the internal wakeup signal
and keyboard interrupt request. The two most
significant bits of Port A are available as GPIO
when this bit is set high.
In the case where KBWEN is low and the INTMR2
bit 0 is low, it will only be possible to wakeup the
device by using the external WAKEUP pin or an-
other enabled interrupt source. The keyboard inter-
rupt capability allows an OS to use either a polled
or interrupt-driven keyboard routine, or a combina-
tion of both.
NOTE:
3.3
The EP7212 has a power-up sequence that should
be followed for proper start up. If any of the below
recommended timing sequences are violated, then
it is possible that the part may not start-up properly.
This could cause the device to get lost and not re-
cover without a hard reset.
The keyboard interrupt is NOT deglitched.
Power-Up Sequence
相關PDF資料
PDF描述
EP7212-CB-A HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
EP7212-CV-A HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
EP7309 HIGH PERFORMANCE LOW POWER SYSTEM ON CHIP ENHANCED DIGITAL AUDIO INTERFACE
EP7309-CB-C CONN MODULAR JACK 8-8 R/A UNSHLD
EP7309-CR-C HIGH PERFORMANCE LOW POWER SYSTEM ON CHIP ENHANCED DIGITAL AUDIO INTERFACE
相關代理商/技術參數
參數描述
EP7212-CB-A 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
EP7212-CV-A 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
EP7212-CV-D 制造商:Rochester Electronics LLC 功能描述:- Bulk
EP7230 功能描述:電氣外殼配件 E-PANEL FITS 72 X 30 RoHS:否 制造商:Hammond Manufacturing 產品:Rack Accessories 類型: 面板寬度: 面板高度: 外部寬度: 外部高度: 外部深度: 顏色:Black
EP7236 功能描述:電氣外殼配件 E-PANEL FITS 72 X 36 RoHS:否 制造商:Hammond Manufacturing 產品:Rack Accessories 類型: 面板寬度: 面板高度: 外部寬度: 外部高度: 外部深度: 顏色:Black
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*