- 您現在的位置：買賣IC網 > PDF目錄362744 > EPC16QC100 (Altera Corporation) 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet PDF資料下載
參數資料
| 型號： | EPC16QC100 |
| 廠商： | Altera Corporation |
| 英文描述： | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| 中文描述： | 2。增強型配置器件（EPC4，EPC8 |
| 文件頁數： | 20/36頁 |
| 文件大?。?/td> | 421K |
| 代理商： | EPC16QC100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
2–20
Configuration Handbook, Volume 2
Altera Corporation
August 2005
Functional Description
The JTAG unit of the configuration controller communicates directly with
the flash memory. The controller processes the ISP instructions and
performs the necessary flash operations. The enhanced configuration
devices support a maximum JTAG
TCK
frequency of 10 MHz.
During JTAG-based ISP, the external flash interface is not available.
Before the JTAG interface programs the flash memory, an optional JTAG
instruction (PENDCFG) can be used to assert the FPGA’s
nCONFIG
pin
(via the
nINIT_CONF
pin). This will keep the FPGA in reset and
terminate any internal flash access. This function prevents contention on
the flash pins when both JTAG ISP and an external FPGA/processor try
to access the flash simultaneously. The
nINIT_CONF
pin is released when
the Initiate Configuration (
nINIT_CONF
) JTAG instruction is updated.
As a result, the FPGA is configured with the new configuration data
stored in flash.
This function can be added to your programming file in the Quartus II
software by enabling the
Initiate configuration after programming
option in the
Programmer options
window (Options menu).
Programming via External Flash Interface
This method allows parallel programming of the flash memory (using the
16-bit data bus). An external processor or FPGA acts as the flash
controller and has access to programming data (via a communication link
such as UART, Ethernet, and PCI). In addition to the program, erase, and
verify operations, the external flash interface supports block/sector
protection instructions.
f
For information on protection commands, areas, and lock bits, refer to
the appropriate flash memory data sheet (Sharp LHF16506 for EPC16
devices and Micron MT28F400B3 for EPC4 devices) on the Altera web
site at
www.altera.com
.
External flash interface programming is only allowed when the
configuration controller has relinquished flash access (by tri-stating its
internal interface). If the controller has not relinquished flash access
(during configuration or JTAG-based ISP), you must hold the controller
in reset before initiating external programming. The controller can be
reset by holding the FPGA
nCONFIG
line at a logic low level. This keeps
the controller in reset by holding the
nSTATUS
-
OE
line low, allowing
external flash access.
1
If initial programming of the enhanced configuration device is
done in-system via the external flash interface, the controller
must be kept in reset by driving the FPGA
nCONFIG
line low to
prevent contention on the flash interface.
相關PDF資料 |
PDF描述 |
|---|---|
| EPC16QI100 | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC8xxx | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC8QC100 | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC8QI100 | 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC16xxx | 435882001 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EPC16QC100N | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPC16QI100 | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPC16QI100N | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPC16UC88 | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPC16UC88AA | 功能描述:IC CONFIG DEVICE 16MBIT 88-UBGA RoHS:否 類別:集成電路 (IC) >> 存儲器 - 用于 FPGA 的配置 Proms 系列:EPC 產品變化通告:Product Discontinuation 28/Jul/2010 標準包裝:98 系列:- 可編程類型:OTP 存儲容量:300kb 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-TSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。