參數資料
型號: EPC8QC100
廠商: Altera Corporation
英文描述: 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet
中文描述: 2。增強型配置器件(EPC4,EPC8
文件頁數: 22/36頁
文件大?。?/td> 421K
代理商: EPC8QC100
2–22
Configuration Handbook, Volume 2
Altera Corporation
August 2005
Pin Description
Table 2–8. External Flash Interface Pins (Part 1 of 2)
Pin Name
Pin Type
Description
A[20..0]
Input
These pins are the address input to the flash memory for read and write
operations. The addresses are internally latched during a write cycle.
When the external flash interface is not used, leave these pins floating
(with the few exceptions noted below). These flash address, data, and
control pins are internally connected to the configuration controller.
In the 100-pin PQFP package, four address pins (
A0
,
A1
,
A15
,
A16
) are
not internally connected to the controller. These loop back connections
must be made on the board between the
C-A[]
and
F-A[]
pins even
when not using the external flash interface. All other address pins are
connected internal to the package.
All address pins are connected internally in the 88-pin Ultra FineLine BGA
package.
Pin
A20
in EPC16 devices, pins
A20
and
A19
in EPC8 devices, and pins
A20
,
A19
, and
A18
in EPC4 devices are no-connects. These pins should
be left floating on the board.
DQ[15..0]
Bidirectional
This is the flash data bus interface between the flash memory and the
controller. The controller or an external source drives
DQ[15..0]
during
the flash command and the data write bus cycles. During the data read
cycle, the flash memory drives the
DQ[15..0]
to the controller or
external device.
Leave these pins floating on the board when the external flash interface is
not used.
CE#
Input
Active low flash input pin that activates the flash memory when asserted.
When it is high, it deselects the device and reduces power consumption
to standby levels. This flash input pin is internally connected to the
controller.
Leave this pin floating on the board when the external flash interface is not
used.
RP#
(1)
Input
Active low flash input pin that resets the flash when asserted. When high,
it enables normal operation. When low, it inhibits write operation to the
flash memory, which provides data protection during power transitions.
This flash input is not internally connected to the controller. Hence, an
external loop back connection between
C-RP#
and
F-RP#
must be made
on the board even when you are not using the external flash interface.
When using the external flash interface, connect the external device to the
RP#
pin with the loop back.
相關PDF資料
PDF描述
EPC8QI100 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet
EPC16xxx 435882001
EPC4QC100 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet
EPC4QI100 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet
EPC16UC88 2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet
相關代理商/技術參數
參數描述
EPC8QC100N 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 8Mb 50 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20
EPC8QI100 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 8Mb 50 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20
EPC8QI100N 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 8Mb 50 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20
EPC8XXX 制造商:ALTERA 制造商全稱:Altera Corporation 功能描述:2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet
EPC-9 制造商:Curtis Industries 功能描述: 制造商:Curtis Industries 功能描述:Conn Barrier Strip 9 POS 9.52mm Solder ST Thru-Hole 15A