- 您現在的位置：買賣IC網 > PDF目錄362799 > EV3205DJ-00A (Monolithic Power Systems, Inc.) 1.3MHz Fixed Frequency 5 White LED Driver PDF資料下載
參數資料
| 型號： | EV3205DJ-00A |
| 廠商： | Monolithic Power Systems, Inc. |
| 英文描述： | 1.3MHz Fixed Frequency 5 White LED Driver |
| 中文描述： | 1.3MHz固定頻率5白光LED驅動器 |
| 文件頁數： | 5/6頁 |
| 文件大?。?/td> | 281K |
| 代理商： | EV3205DJ-00A |
MP3205 – 1.3 MHz FIXED FREQUENCY 5 WHITE LED DRIVER
MP3205 Rev. 1.3
7/13/2005
www.MonolithicPower.com
5
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
2005 MPS. All Rights Reserved.
TM
Setting the LED Current
The LED current is controlled by the feedback
resistor, R1, in Figure 2. The current through
the LEDs is given by the equation 104mV/R1.
Table 1 shows the selection of resistors for a
given LED current.
Table 1—I
LED
vs. R1
I
LED
(mA)
1
5
10
15
20
R1 (
)
104
20.8
10.4
6.93
5.2
Analog and Digital Dimming
There are three different ways to control dimming
for the MP3205 during normal operation. The first
way uses a DC voltage to control the feedback
voltage. This can be seen in Figure 6. As the DC
voltage increases, current starts flowing down R1,
R2 and R3. The loop will continue to regulate the
feedback voltage to 104mV. Thus the current has
to decrease through the LEDs by the same
amount of current as is being injected from the
DC voltage source. With a V
DC
from 0V to 2V, the
resistor values shown for R2 and R3 can control
the LED current from 0mA to 20mA.
MP3205
LED1
LED2
LED3
FB
3
V
DC
MP3205_F06_S01
Figure 6—Dimming Control Using a DC Voltage
Other applications need to use a logic signal to
do the dimming. This can be seen in Figure 7.
The PWM signal is applied to the EN pin of the
MP3205. The LEDs will switch between full load
to completely shut off. The average current
through the LEDs will increase proportionally to
the duty cycle of the PWM signal. The PWM
signal used in Figure 7 should be 1KHz or
below due to the soft start function.
PWM
MP3205
LED1
LED2
LED3
FB
3
MP3205_F07_S01
EN
4
Figure 7—PWM Dimming Control Using a
Logic Signal
If the PWM signal is above 1KHz, dimming can
be achieved by using the circuit shown in
Figure 8.
PWM
MP3205
LED1
LED2
LED3
FB
3
MP3205_F08_S01
Figure 8—Dimming Control Using a Filtered
PWM Signal
Layout Considerations
Careful attention must be paid to the PCB
board layout and component placement. Proper
layout of the high frequency switching path is
critical to prevent noise and electromagnetic
interference problems. Due to the high
frequency switching the length and area of all
the traces connected to the switch node should
be minimized. Refer to the evaluation board
EV3205DJ-00A
for
a
the
B
MP3205.
sample
layout
of
相關PDF資料 |
PDF描述 |
|---|---|
| EV3213DH-00A | 700KHz/1.3MHz Boost Converter with a 3.5A Switch |
| EV4101 | 32-bit Microprocessor that Executes MIPS I,a Subset of MIPS II,and a Subset of the MIPS16 Instructions.(32位微處理器（執行MIPS I,MIPS II的子集,MIPS16的子集指令）) |
| EV5103 | G5103 White LED Demo Board V1.0 |
| EV5103-10 | G5103 White LED Demo Board V1.0 |
| EV6001DN-00A | Monolithic Flyback/Forward DC-DC Converter Evaluation Board |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EV3212X05XA_D5X WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| EV3213DH-00A | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:700KHz/1.3MHz Boost Converter with a 3.5A Switch |
| EV322 | 制造商:FASTRAX 功能描述:KIT EVAL GPS RECEIVER UC322 制造商:FASTRAX 功能描述:UC322, GPS RECEIVER, 20-CHANNEL, EVALUATION BOARD; Silicon Manufacturer:Fastrax; Silicon Core Number:UC322; Kit Application Type:Sensing - Navigation, Position; Application Sub Type:GPS Receiver; MCU Supported Families:SiRFstarIII ;RoHS Compliant: Yes |
| EV32C1 | 制造商:ECLIPTEK 制造商全稱:Ecliptek Corporation 功能描述:CERAMIC SMD3.3V HCMOS/TTL VCXO |
| EV32C1A1A1-35.328MTR | 制造商:ECLIPTEK 制造商全稱:Ecliptek Corporation 功能描述:CERAMIC SMD3.3V HCMOS/TTL VCXO |
發布緊急采購，3分鐘左右您將得到回復。