參數資料
型號： EVAL-AD1928EB
廠商： Analog Devices, Inc.
元件分類： Codec
英文描述： 2 ADC/8 DAC with PLL, 192 kHz, 24-Bit Codec
中文描述： 2藝發局/ 8鎖相環，192千赫，24位編解碼器數模轉換器
文件頁數： 14/32頁
文件大小： 354K
代理商： EVAL-AD1928EB
AD1928
ground connections with other unrelated digital output signals.
When the PLL is used, jitter in the reference clock is attenuated
above a certain frequency depending on the loop filter.
RESET AND POWER-DOWN
The function of the RST pin sets all the control registers to
their default settings. To avoid pops, reset does not power
down the analog outputs. After RST is deasserted and the PLL
acquires lock condition, an initialization routine runs inside the
AD1928. This initialization lasts for approximately 256 master
clock cycles.
The power-down bits in the PLL and Clock Control 0, DAC
Control 1, and ADC Control 1 registers power down the
respective sections. All other register settings are retained. The
reset pin, PD/RST, should be pulled low by an external resistor
to guarantee proper startup.
SERIAL CONTROL PORT
The AD1928 has an SPI control port that permits programming
and reading back of the internal control registers for the ADCs,
DACs, and clock system. There is also a standalone mode
Rev. 0 | Page 14 of 32
available for operation without serial control that is configured
at reset using the serial control pins. All registers are set to
default, except the internal master clock enable is set to 1
and ADC BCLK and LRCLK master/slave is set by the COUT
pin. Standalone mode only supports stereo mode with an I
2
S
data format and 256 f
S
master clock rate. Refer to Table 11 for
details. It is recommended to use a weak pull-up resistor on
CLATCH in applications that have a microcontroller. This pull-
up resistor ensures that the AD1928 recognizes the presence of
a microcontroller.
The SPI control port of the AD1928 is a 4-wire serial control
port. The format is similar to the Motorola SPI format, except
the input data-word is 24 bits wide. The serial bit clock and
latch can be completely asynchronous to the sample rate of the
ADCs and DACs. Figure 11 shows the format of the SPI signal.
The first byte is a global address with a read/write bit. For the
AD1928, the address is 0x04, shifted left 1 bit due to the R/W
bit. The second byte is the AD1928 register address and the
third byte is the data.
Table 11. Standalone Mode Selection
ADC Clocks
Slave
Master
CIN
0
0
COUT
0
1
CCLK
0
0
CLATCH
0
0
D0
D0
D8
D8
D22
D23
D9
D9
CLATCH
CCLK
CIN
COUT
t
CCH
t
CCL
t
CDS
t
CDH
t
CLS
t
CCP
t
CLH
t
COTS
t
COD
t
COE
0
Figure 11. Format of SPI Signal
相關PDF資料
PDF描述
EVAL-AD1938EB 4 ADC/8 DAC with PLL, 192 kHz, 24 Bit CODEC
EVAL-AD1939EB 4 ADC/8 DAC with PLL, 192 kHz, 24 Bit CODEC
EVAL-AD1935EB 4 ADC/8 DAC with PLL, 192 kHz, 24 Bit CODEC
EVAL-AD1936EB 4 ADC/8 DAC with PLL, 192 kHz, 24 Bit CODEC
EVAL-AD1937EB 4 ADC/8 DAC with PLL, 192 kHz, 24 Bit CODEC
相關代理商/技術參數
參數描述
EVAL-AD1928EBZ 制造商:AD 制造商全稱:Analog Devices 功能描述:2 ADC/8 DAC with PLL, 192 kHz, 24-Bit Codec
EVAL-AD1934EB 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel DAC with PLL, 192 kHz, 24 Bits
EVAL-AD1935EB 制造商:AD 制造商全稱:Analog Devices 功能描述:4 ADC/8 DAC with PLL, 192 kHz, 24 Bit CODEC
EVAL-AD1936EB 制造商:AD 制造商全稱:Analog Devices 功能描述:4 ADC/8 DAC with PLL, 192 kHz, 24 Bit CODEC
EVAL-AD1937AZ 功能描述:BOARD EVAL FOR AD1937 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*