參數資料
型號： EVAL-ADF7012EB5
廠商： Analog Devices, Inc.
英文描述： Multichannel ISM Band FSK/GFSK/OOK/GOOK/ASK Transmitter
中文描述： 多通道ISM頻段FSK信號/的GFSK /元件Ook /約克/ ASK發射
文件頁數： 23/28頁
文件大?。?/td> 772K
代理商： EVAL-ADF7012EB5
ADF7012
915 MHZ OPERATION
The recommendations here are guidelines only. The design
should be subject to internal testing prior to FCC site testing.
Matching components need to be adjusted for board layout.
Rev. 0 | Page 23 of 28
FCC 15.247 and FCC 15.249 are the main regulations governing
operation in the 902 MHz to 928 MHz Band. FCC 15.247
requires some form of spectral spreading. Typically, the
ADF7012 would be used in conjunction with the frequency
hopping spread spectrum (FHSS) or it may be used in
conjunction with the digital modulation standard which
requires large deviation frequencies. Output power of < 1 W
is tolerated on certain spreading conditions.
Compliance with FCC 15.249 limits the output power to
1.5 dBm, but does not require spreading. There are many
different applications in this band, including remote controls
for security, sensor interrogation, metering, and home control.
Design Criteria
915.2MHz center frequency
FSK modulation
10 dBm output power
200 m range
Meets FCC 15.247
38.4 kbps data rate
The center frequency is 915.2 MHz. It is possible to operate
the VCO at this frequency. Figure 36 shows the inductor value
vs. center frequency. The inductor chosen is 1.6 nH. Coilcraft
inductors such as 0603-CS-1N6XJBU are recommended.
Additional hopping frequencies can easily be generated by
changing the N value.
Crystal and PFD
The phase noise requirement is such to ensure that the 20 dB
bandwidth requirements are met. These are dependant on the
channel spacing chosen. A typical channel spacing would be
400 kHz, which would allow 50 channels in 20 MHz and enable
the design to avoid the edges of the band.
The PFD is chosen so as to minimize spurious levels. There are
beat note spurious levels at 910 MHz and 920 MHz, but the
level is usually significantly less than the modulation power.
They are also attenuated quickly by the loop filter to ensure a
quick crystal power-up time.
PFD = 10 MHz Power-Up Time 1.8 ms (approximately).
Figure 10 shows a typical power-on time for a 4 MHz crystal.
N-Divider
The N divider is determined as being:
Nint = 91
Nfrac = (2130)/4096
VCO divide-by-2 is not enabled
Deviation
The deviation is set to ±19.2 kHz so as to accommodate a
simple receiver architecture, and also to ensure the available
spectrum is used efficiently.
The modulation steps available are in 10 MHz/2
14
:
Modulation steps = 610 Hz
Modulation number = 19.2 kHz/610 Hz = 31.
Bias Current
Because low current is desired, a 3 mA VCO bias can be used
and still ensure oscillation at 928 MHz. Additional bias current
reduces any spurious noise, but increases current consumption.
A 3 mA bias current gives the best spurious vs. phase noise
trade-off.
The PA bias should be set to 5.5 mA to achieve 10 dBm power.
Loop Filter Bandwidth
The loop filter is designed with ADIsimPLL Version 2.5. A
data rate of 170 kHz is chosen, which allows for data rates of
> 38.4 kbps. It also attenuates the beat note spurs quickly to
ensure they have no effect on system performance.
Design of Harmonic Filter
The main requirement of the harmonic filter should ensure
that the third harmonic level is < 41.5 dBm. A fifth-order
Chebyshev filter is recommended to achieve this, and a
suggested starting point is given next. The Pi format is chosen
to minimize the number of inductors in the system.
Component Values—Crystal: 10 MHz
Loop Filter
Icp
1.44 mA
LBW
170 kHz
C1
470 pF
C2
12 nF
C3
120 pF
R1
470 V
R2
1.8 kV
Matching
L1
L2
C14
C15
27 nH
6.2 nH
470 pF
Open
Harmonic Filter
L4
L5
CF1
CF2
CF3
8.2 nH
8.2 nH
4.7 pF
6.8 pF
4.7 pF
相關PDF資料
PDF描述
EVAL-ADG936-REB Wideband 4 GHz, 36 dB Isolation at 1 GHz, CMOS 1.65 V to 2.75 V, Dual SPDT
EVAL-ADG936EB Wideband 4 GHz, 36 dB Isolation at 1 GHz, CMOS 1.65 V to 2.75 V, Dual SPDT
EVAL-ADM1022 Evaluation Board for Microprocessor System Temperature Monitor
EVAL-ADM1023 Evaluation Board for Microprocessor System Temperature Monitor
EVAL-ADM1026EB Complete Thermal and System Management Controller
相關代理商/技術參數
參數描述
EVAL-ADF7020-1DBZ4 功能描述:BOARD EVAL ADF7020-1 405-435MHZ RoHS:是 類別:RF/IF 和 RFID >> RF 評估和開發套件，板 系列:- 標準包裝:1 系列:- 類型:GPS 接收器 頻率:1575MHz 適用于相關產品:- 已供物品:模塊 其它名稱:SER3796
EVAL-ADF7020-1DBZ5 功能描述:BOARD EVAL ADF7020-2 ADJ FREQ RoHS:是 類別:RF/IF 和 RFID >> RF 評估和開發套件，板 系列:- 標準包裝:1 系列:- 類型:GPS 接收器 頻率:1575MHz 適用于相關產品:- 已供物品:模塊 其它名稱:SER3796
EVAL-ADF7020-1DBZ6 功能描述:BOARD EVAL ADF7020-1 470-510MHZ RoHS:是 類別:RF/IF 和 RFID >> RF 評估和開發套件，板 系列:- 標準包裝:1 系列:- 類型:GPS 接收器 頻率:1575MHz 適用于相關產品:- 已供物品:模塊 其它名稱:SER3796
EVAL-ADF7020-1DBZ7 功能描述:BOARD EVAL ADF7020-1 310-340MHZ RoHS:是 類別:RF/IF 和 RFID >> RF 評估和開發套件，板 系列:- 標準包裝:1 系列:- 類型:GPS 接收器 頻率:1575MHz 適用于相關產品:- 已供物品:模塊 其它名稱:SER3796
EVAL-ADF7020-1DBZ8 功能描述:BOARD EVAL ADF7020-1 128-142MHZ RoHS:是 類別:RF/IF 和 RFID >> RF 評估和開發套件，板 系列:- 標準包裝:1 系列:- 類型:GPS 接收器 頻率:1575MHz 適用于相關產品:- 已供物品:模塊 其它名稱:SER3796
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*