- 您現在的位置：買賣IC網 > PDF目錄362803 > EVAL-ADM1066LFEB (Analog Devices, Inc.) Multisupply Supervisor/Sequencer with Margining Control and Auxiliary ADC Inputs PDF資料下載
參數資料
| 型號： | EVAL-ADM1066LFEB |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | ADC |
| 英文描述： | Multisupply Supervisor/Sequencer with Margining Control and Auxiliary ADC Inputs |
| 中文描述： | Multisupply監/同裕量控制和輔助ADC輸入序列 |
| 文件頁數： | 16/32頁 |
| 文件大?。?/td> | 861K |
| 代理商： | EVAL-ADM1066LFEB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
ADM1066
OUTPUTS
SUPPLY SEQUENCING THROUGH
CONFIGURABLE OUTPUT DRIVERS
Supply sequencing is achieved with the ADM1066 using the
programmable driver outputs (PDOs) on the device as control
signals for supplies. The output drivers can be used as logic
enables or as FET drivers.
Rev. 0 | Page 16 of 32
The sequence in which the PDOs are asserted (and, therefore,
the supplies are turned on) is controlled by the sequencing
engine (SE). The SE determines what action is to be taken with
the PDOs based on the condition of the inputs of the ADM1066.
Therefore, the PDOs can be set up to assert when the SFDs are
in tolerance, the correct input signals are received on the VXn
digital pins, no warnings are received from any of the inputs of
the device, and so on. The PDOs can be used for a variety of
functions. The primary function is to provide enable signals for
LDOs or dc/dc converters, which generate supplies locally on a
board. The PDOs can also be used to provide a POWER_GOOD
signal when all the SFDs are in tolerance, or a RESET output if
one of the SFDs goes out of specification (this can be used as a
status signal for a DSP, FPGA, or other microcontroller).
The PDOs can be programmed to pull up to a number of
different options. The outputs can be programmed as follows:
Open-drain (allowing the user to connect an external pull-up
resistor)
Open-drain with weak pull-up to V
DD
Push/pull to V
DD
Open-drain with weak pull-up to VPn
Push/pull to VPn
Strong pull-down to GND
Internally charge-pumped high drive (12 V, PDO1–6 only)
The last option (available only on PDO1–6) allows the user to
directly drive a voltage high enough to fully enhance an external
N-FET, which is used to isolate, for example, a card-side voltage
from a backplane supply (a PDO can sustain greater than 10.5 V
into a 1 μA load). The pull-down switches can also be used to
drive status LEDs directly.
The data driving each of the PDOs can come from one of three
sources. The source can be enabled in the PnPDOCFG con-
figuration register (see the AN-698 application note for details).
The data sources are
Output from the SE.
Directly from the SMBus. A PDO can be configured so that
the SMBus has direct control over it. This enables software
control of the PDOs. Therefore, a microcontroller can be
used to initiate a software power-up/power-down sequence.
On-Chip Clock. A 100 kHz clock is generated on the device.
This clock can be made available on any of the PDOs. It can
be used, for example, to clock an external device such as
an LED.
By default, the PDOs are pulled to GND by a weak (20 k) on-
chip pull-down resistor. This is also the condition of the PDOs
on power-up, until the configuration is downloaded from
EEPROM and the programmed setup is latched. The outputs
are actively pulled low once a supply of 1 V or greater is on VPn
or VH. The outputs remain high impedance prior to 1 V appear-
ing on VPn or VH. This provides a known condition for the
PDOs during power-up. The internal pull-down can be over-
driven with an external pull-up of suitable value tied from the
PDO pin to the required pull-up voltage. The 20 k resistor
must be accounted for in calculating a suitable value. For
example, if PDOn must be pulled up to 3.3 V, and 5 V is available
as an external supply, the pull-up resistor value is given by
3.3 V = 5 V × 20 k/(
R
UP
+ 20 k)
Therefore,
R
UP
= (100 k 66 k)/3.3 = 10 k
0
PDO
SE DATA
CFG4
CFG5
CFG6
SMBus DATA
CLK DATA
1
2
1
2
VP1
SEL
VP4
1
2
V
DD
VFET (PDO1-6 ONLY)
2
Figure 25. Programmable Driver Output
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-ADM1066TQEB | Multisupply Supervisor/Sequencer with Margining Control and Auxiliary ADC Inputs |
| EVAL-ADN2819-CML | Multirate to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp |
| EVAL-ADN2843 | 10.709 Gbps Laser Diode Driver Chipset |
| EVAL-ADT7466EB | dBCool Remote Thermal Controller and Voltage Monitor |
| EVAL-ADUC846QS | MicroConverter, Dual 16-Bit ADCs with Embedded 62kB FLASH MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADM1066LFEBZ | 制造商:Analog Devices 功能描述:EVAL KIT FOR THE ADM1066 SUPER SEQUENCERS - Bulk |
| EVAL-ADM1066TQEB | 制造商:AD 制造商全稱:Analog Devices 功能描述:Multisupply Supervisor/Sequencer with Margining Control and Auxiliary ADC Inputs |
| EVAL-ADM1066TQEBZ | 功能描述:BOARD EVALUATION FOR ADM1066TQ RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-ADM1067LFEB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-ADM1067LFEBZ | 制造商:Analog Devices 功能描述:Evaluation Board For Super Sequencer With Open-Loop Margining DACs 制造商:Analog Devices 功能描述:SUPER SEQUENCER W/ OPEN-LOOP MARGINING DACS - Bulk |
發布緊急采購，3分鐘左右您將得到回復。