參數資料
型號： EVAL-ADM1066LFEB
廠商： Analog Devices, Inc.
元件分類： ADC
英文描述： Multisupply Supervisor/Sequencer with Margining Control and Auxiliary ADC Inputs
中文描述： Multisupply監/同裕量控制和輔助ADC輸入序列
文件頁數： 27/32頁
文件大小： 861K
代理商： EVAL-ADM1066LFEB
ADM1066
Rev. 0 | Page 27 of 32
9
0
1
9
9
1
1
9
1
START BY
MASTER
ACK. BY
SLAVE
ACK. BY
MASTER
ACK. BY
MASTER
NO ACK.
FRAME 2
DATA BYTE
FRAME 1
SLAVE ADDRESS
FRAME N
DATA BYTE
FRAME 3
DATA BYTE
SCL
SDA
R/W
STOP
BY
MASTER
SCL
(CONTINUED)
SDA
(CONTINUED)
D7
A0
A1
1
1
1
0
0
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
Figure 37. General SMBus Read Timing Diagram
0
SCL
SDA
P
S
S
P
t
SU;STO
t
HD;STA
t
SU;STA
t
SU;DAT
t
HD;DAT
t
HD;STA
t
HIGH
t
BUF
t
LOW
t
R
t
F
Figure 38. Serial Bus Timing Diagram
SMBus Protocols for RAM and EEPROM
The ADM1066 contains volatile registers (RAM) and nonvola-
tile registers (EEPROM). User RAM occupies address locations
from 0x00 to 0xDF; EEPROM occupies addresses from 0xF800
to 0xFBFF.
Data can be written to and read from both RAM and EEPROM
as single data bytes. Data can be written only to unprogrammed
EEPROM locations. To write new data to a programmed loca-
tion, it must first be erased. EEPROM erasure cannot be done at
the byte level. The EEPROM is arranged as 32 pages of 32 bytes
each, and an entire page must be erased.
Page erasure is enabled by setting Bit 2 in the UPDCFG register
(Address 0x90) to 1. If this bit is not set, page erasure cannot
occur, even if the command byte (0xFE) is programmed across
the SMBus.
WRITE OPERATIONS
The SMBus specification defines several protocols for different
types of read and write operations. The following abbreviations
are used in the diagrams:
S
P
R
W
A
A
Start
Stop
Read
Write
Acknowledge
No acknowledge
The ADM1066 uses the following SMBus write protocols.
Send Byte
In a send byte operation, the master device sends a single
command byte to a slave device, as follows:
1.
The master device asserts a start condition on SDA.
2.
The master sends the 7-bit slave address followed by the
write bit (low).
3.
The addressed slave device asserts ACK on SDA.
4.
The master sends a command code.
5.
The slave asserts ACK on SDA.
6.
The master asserts a stop condition on SDA and the
transaction ends.
In the ADM1066, the send byte protocol is used for two
purposes:
To write a register address to RAM for a subsequent single
byte read from the same address, or a block read or write
starting at that address, as shown in Figure 39.
0
2
4
1
3
SLAVE
ADDRESS
REGISTER
ADDRESS
(0x00 TO 0xDF)
S
W
A
A
5
6
P
Figure 39. Setting a RAM Address for Subsequent Read
相關PDF資料
PDF描述
EVAL-ADM1066TQEB Multisupply Supervisor/Sequencer with Margining Control and Auxiliary ADC Inputs
EVAL-ADN2819-CML Multirate to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp
EVAL-ADN2843 10.709 Gbps Laser Diode Driver Chipset
EVAL-ADT7466EB dBCool Remote Thermal Controller and Voltage Monitor
EVAL-ADUC846QS MicroConverter, Dual 16-Bit ADCs with Embedded 62kB FLASH MCU
相關代理商/技術參數
參數描述
EVAL-ADM1066LFEBZ 制造商:Analog Devices 功能描述:EVAL KIT FOR THE ADM1066 SUPER SEQUENCERS - Bulk
EVAL-ADM1066TQEB 制造商:AD 制造商全稱:Analog Devices 功能描述:Multisupply Supervisor/Sequencer with Margining Control and Auxiliary ADC Inputs
EVAL-ADM1066TQEBZ 功能描述:BOARD EVALUATION FOR ADM1066TQ RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
EVAL-ADM1067LFEB 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk
EVAL-ADM1067LFEBZ 制造商:Analog Devices 功能描述:Evaluation Board For Super Sequencer With Open-Loop Margining DACs 制造商:Analog Devices 功能描述:SUPER SEQUENCER W/ OPEN-LOOP MARGINING DACS - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*