參數資料
型號： EVAL-ADN2819-CML
廠商： Analog Devices, Inc.
元件分類： 限幅放大器
英文描述： Multirate to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp
中文描述： 多速率為2.7 Gb / s的集成時鐘和數據恢復芯片限幅放大器
文件頁數： 10/24頁
文件大?。?/td> 570K
代理商： EVAL-ADN2819-CML
ADN2819
LOS RESPONSE TIME
The LOS response time is the delay between the removal of the
input signal and indication of loss of signal (LOS) at SDOUT.
The ADN2819’s response time is 300 ns typ when the inputs are
dc-coupled. In practice, the time constant of ac-coupling at the
quantizer input determines the LOS response time.
Rev. B | Page 10 of 24
JITTER SPECIFICATIONS
The ADN2819 CDR is designed to achieve the best bit-error-
rate (BER) performance, and has exceeded the jitter transfer,
generation, and tolerance specifications proposed for
SONET/SDH equipment defined in the Telcordia Technologies
specification.
Jitter is the dynamic displacement of digital signal edges from
their long-term average positions measured in UI (unit
intervals), where 1 UI = 1 bit period. Jitter on the input data
can cause dynamic phase errors on the recovered clock
sampling edge. Jitter on the recovered clock causes jitter on the
retimed data.
The following sections summarize the specifications of the jitter
generation, transfer, and tolerance in accordance with the
Telcordia document (GR-253-CORE, Issue 3, September 2000)
for the optical interface at the equipment level, and the
ADN2819 performance with respect to those specifications.
Jitter Generation
Jitter generation specification limits the amount of jitter that
can be generated by the device with no jitter and wander
applied at the input. For OC-48 devices, the band-pass filter has
a 12 kHz high-pass cutoff frequency, with a roll-off of
20 dB/decade and a low-pass cutoff frequency of at least
20 MHz. The jitter generated should be less than 0.01 UI rms
and 0.1 UI p-p.
Jitter Transfer
Jitter transfer function is the ratio of the jitter on the output
signal to the jitter applied on the input signal versus the
frequency. This parameter measures the limited amount of jitter
on an input signal that can be transferred to the output signal
(see Figure 11).
SLOPE = –20dB/DECADE
JITTER FREQUENCY (kHz)
0.1
J
f
C
ACCEPTABLE
RANGE
0
Figure 11. Jitter Transfer Curve
Jitter Tolerance
Jitter tolerance is defined as the peak-to-peak amplitude of the
sinusoidal jitter applied on the input signal that causes a 1 dB
power penalty. This is a stress test that is intended to ensure no
additional penalty is incurred under the operating conditions
(see Figure 12). Figure 13 shows the typical OC-48 jitter
tolerance performance of the ADN2819.
SLOPE = –20dB/DECADE
f
0
f
1
f
2
f
3
f
4
JITTER FREQUENCY (Hz)
15
1.5
0.15
I
0
Figure 12. SONET Jitter Tolerance Mask
MODULATION FREQUENCY (Hz)
10
1k
100k
10M
100
10
0.1
A
1
100
10k
1M
1
ADN2819
OC-48 SONET MASK
0
Figure 13. OC-48 Jitter Tolerance Curve
相關PDF資料
PDF描述
EVAL-ADN2843 10.709 Gbps Laser Diode Driver Chipset
EVAL-ADT7466EB dBCool Remote Thermal Controller and Voltage Monitor
EVAL-ADUC846QS MicroConverter, Dual 16-Bit ADCs with Embedded 62kB FLASH MCU
EVAL-ADUC846QSP MicroConverter, Dual 16-Bit ADCs with Embedded 62kB FLASH MCU
EVAL-ADV7174EBM Chip Scale PAL/NTSC Video Encoder with Advanced Power Management
相關代理商/技術參數
參數描述
EVAL-ADN2830-U1 制造商:Analog Devices 功能描述:Avg power controller for CW lasers EVB 制造商:Analog Devices 功能描述:AVG POWER CONTROLLER FOR CW LASERS EVB - Bulk
EVAL-ADN2841-32-OP 制造商:Analog Devices 功能描述:EVAL BD FOR OPTODRVRS, DUAL-LOOP 50MBPS-2.7GBPS LASER DIODE - Bulk
EVAL-ADN2841-48-OP 制造商:Analog Devices 功能描述:Evaluation Board For Opto-Drivers, Dual-Loop 50Mbps-2.7Gbps LASER Diode Driver 制造商:Analog Devices 功能描述:EVAL BD FOR OPTODRVRS, DUAL-LOOP 50MBPS-2.7GBPS LASER DIODE - Bulk
EVAL-ADN2841-U2 制造商:Analog Devices 功能描述:EVAL BD FOR OPTODRVRS, DUAL-LOOP 50MBPS-2.7GBPS LASER DIODE - Bulk
EVAL-ADN2843 制造商:AD 制造商全稱:Analog Devices 功能描述:10.709 Gbps Laser Diode Driver Chipset
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*