- 您現在的位置：買賣IC網 > PDF目錄384414 > HI-6010JTF (HOLT INTEGRATED CIRCUITS INC) ARINC 429 TRANSMITTER/RECEIVER FOR 8 BIT BUS PDF資料下載
參數資料
| 型號： | HI-6010JTF |
| 廠商： | HOLT INTEGRATED CIRCUITS INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | ARINC 429 TRANSMITTER/RECEIVER FOR 8 BIT BUS |
| 中文描述： | 1 CHANNEL(S), SERIAL COMM CONTROLLER, PQCC28 |
| 封裝： | ROHS COMPLIANT, PLASTIC, LCC-28 |
| 文件頁數： | 4/12頁 |
| 文件大?。?/td> | 101K |
| 代理商： | HI-6010JTF |
USING THE TRANSMITTER
The transmitter logic is independent of the receiver except in
thefollowingways:
1.
2.
Self Test
Parity Option
In self test the transmitter outputs route to the receiver inputs
internallyandtheTXD0andTXD1outputsareinhibited.
When parity is enabled, both the receiver and transmitter are
affected. Odd parity is automatically generated in the 32nd
bitifthisoptionisselected.
This output goes high for 1 transmitter error and 3 receiver
errors. To determine which error is being flagged, read the
Status Register. Reading the Status Register also clears the
error flag. The transmitter will not function until the error is
cleared. ItcanalsobeclearedbyMRgoinghigh.
Theonlypossibletransmittererrorisgeneratedwhenrunning
in8bitmode. Forthetransmitterthismeansloadingthelast3
bytes while the transmission is in progress. Failure to load a
byte before the previous byte's 8th bit is transmitted will
generatetheerror, indicatedbystatusbitSR7set toa1.
This pin is a hardware gate for transmissions.
transmitter buffer is loaded and Control Register bit CR0 is a
one,theonlyinhibitofthetransmitterwouldbefor
one.
When taken low, transmission of an ARINC word is
enabled. Itmaybepulsedtoreleaseeachtransmittedword.
If the
tobea
The data rate of transmission is controlled by this pin. This
clockmustbe4Xthedesireddaterate.
ThispinalongwiththeControlRegistersetsthefunctioningof
thechip. Forthetransmitter:
HARDWARE CONTROL OF THE TRANSMITTER
PIN 2 - WEF
PIN3 -
PIN4 - TXC
PIN5 - HFSandtheCONTROLREGISTER
CTS
CTS
PIN7 - TXE
Whenever a transmission begins, this pin goes low and
returnshighafterthetransmissioniscomplete.
PIN9 - TXRDY
Whenever TXRDY is a one, data may be written into the
transmitter buffer. In 8 bit "one byte at a time" mode, this pin
maybemonitoredtoindicatewhentowritethenext8bits.
PIN10 - TXD0 and PIN11 - TXD1
TXD0 will go high during a transmission if the data is zero.
TXD1 goes high if data is a one. When both pins are low this
is referred to as the Null state.
transmitter chip, such as the HI-3182, HI-3183, HI-8585 or
HI-8586 is connected to these pins to translate the 5 volt
levelstotheproperARINCbuslevels.
Typically an ARINC
DataisnotoutputwhentheHI-6010isinself-testmode.
By writing into the Control Register and reading the Status
Register, the controlling processor can operate the
transmitter independent of the flags at the pins.
TransmissioncanbeinitiatedbychangingCR0froma0toa1
afterthetransmitterbufferhasbeenloaded. ThentheStatus
Registermaybemonitoredasfollows:
SOFTWARECONTROLOFTHETRANSMITTER
CablingNoise
The HI-6010 has TTL compatible inputs and therefore
they are susceptible to noise near ground. If the data bus
is passed by ribbon cable or the equivalent to the device
under test, it is possible to get significant glitches on the
MasterResetline. Theproblemwillappeartobeapattern
sensitivefailure. Onecureissimplytoadequatelybypass
MasterReset. AnotheristobuffertheHI-6010inputsnear
thechip.
After Master Reset the HI-6010 receiver must see a word
gapbeforethefirstARINCdatabit.
Error flags must be cleared by either a Status Register
Read or by a Master Reset. The operation of either the
transmitterorthereceiverisinhibiteduponerror.
ReceiverSeemsDead
APPLICATIONS TIPS
CONTROL
BIT NAME
PROGRAM
VALUE
PIN 5
VALUE
OPERATION
CR0
0
1
X
X
Transmitter is disabled
Transmitter is enabled
CR4
0
1
X
X
Not in self test
Self test enabled
CR5
0
1
0
1
0
0
1
1
8 bit mode + data in 32nd bit
8 bit mode + parity enabled
32 bit mode with parity enabled
8 bit mode with parity enabled
SR0
0
1
Do not load the transmitter buffer
Ready to load the transmitter buffer
SR2
0
1
Transmission in progress
Transmitter is idle
SR7
0
1
No transmission error
8 bit mode only error for underwriting data
STATUS BIT
VALUE
MEANING
PIN6-MR
The chip is initialized whenever this pin goes high.
Control Register is set to 0X10 0101 (CR7 - CR0). For the
transmitter this sets up 8 bit mode with the transmitter
enabled.
The
HI-6010
HOLT INTEGRATED CIRCUITS
4
相關PDF資料 |
PDF描述 |
|---|---|
| HI-6110 | MIL-STD-1553 / MIL-STD-1760 BC / RT / MT Message Processor |
| HI-6110PQI | MIL-STD-1553 / MIL-STD-1760 BC / RT / MT Message Processor |
| HI-6110PQIF | MIL-STD-1553 / MIL-STD-1760 BC / RT / MT Message Processor |
| HI-6110PQM | MIL-STD-1553 / MIL-STD-1760 BC / RT / MT Message Processor |
| HI-6110PQMF | MIL-STD-1553 / MIL-STD-1760 BC / RT / MT Message Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HI-6011 | 制造商:HOLTIC 制造商全稱:Holt Integrated Circuits 功能描述:ARINC 429 Transmitter / Dual Receiver for 8-Bit Bus |
| HI-6011CDT | 制造商:HOLTIC 制造商全稱:Holt Integrated Circuits 功能描述:ARINC 429 Transmitter / Dual Receiver for 8-Bit Bus |
| HI6-0201-5 | 功能描述:模擬開關 IC Quad SPST CMOS Analog Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| HI6-0201-5-T | 制造商:Maxim Integrated Products 功能描述:Quad SPST CMOS Analog Switch |
| HI6-0201-9 | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發布緊急采購，3分鐘左右您將得到回復。