- 您現在的位置：買賣IC網 > PDF目錄379204 > IBM13M32734BCD (IBM Microeletronics) 32M x 72 2-Bank Registered/Buffered SDRAM Module(32M x 72 2組寄存/緩沖同步動態RAM模塊) PDF資料下載
參數資料
| 型號： | IBM13M32734BCD |
| 廠商： | IBM Microeletronics |
| 英文描述： | 32M x 72 2-Bank Registered/Buffered SDRAM Module(32M x 72 2組寄存/緩沖同步動態RAM模塊) |
| 中文描述： | 32M × 72配置2，銀行注冊/緩沖內存模組（32M × 72配置2組寄存/緩沖同步動態內存模塊） |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 579K |
| 代理商： | IBM13M32734BCD |
IBM13M32734BCD
32M x 72 2-Bank Registered/Buffered SDRAM Module
IBM Corporation. All rights reserved.
Use is further subject to the provisions at the end of this document.
Page 6 of 20
19L7143.E93758B
2/99
Input/Output Functional Description
Symbol
Type
Signal
Polarity
Function
CK0 - CK3
Input
Pulse
Positive
Edge
The system clock inputs. All of the SDRAM inputs are sampled on the rising edge of their
associated clock. CK0 drives the PLL. CK1, CK2 & CK3 are terminated.
CKE0
Input
Level
Active
High
Activates the SDRAM CK signal when high and deactivates the CK signal when low. By
deactivating the clocks, CKE low initiates the Power Down mode, Suspend mode, or the
Self Refresh mode.
S0 - S3
Input
Pulse
Active Low
Enables the associated SDRAM command decoder when low and disables the com-
mand decoder when high. When the command decoder is disabled, new commands are
ignored but previous operations continue. Physical Bank 0 is selected by S0 and S2;
Bank 1 is selected by S1 and S3.
RAS, CAS
WE
Input
Pulse
Active Lowoperation to be executed by the SDRAM.
BA0, 1
Input
Level
—
Selects which SDRAM bank of four is activated.
A0 - A9, A11
A10/AP
Input
Level
—
During a Bank Activate command cycle, A0-A11 defines the row address (RA0-RA11)
when sampled at the rising clock edge.
During a Read or Write command cycle, A0-A9 defines the column address (CA0-CA9)
when sampled at the rising clock edge. In addition to the column address, AP is used to
invoke autoprecharge operation at the end of the burst read or write cycle. If AP is high,
autoprecharge is selected and BA0, BA1 defines the bank to be precharged. If AP is low,
autoprecharge is disabled.
During a Precharge command cycle, AP is used in conjunction with BA0, BA1 to control
which bank(s) to precharge. If AP is high, all banks will be precharged regardless of the
state of BA0 or BA1. If AP is low, then BA0 and BA1 are used to define which bank to
precharge.
DQ0 - DQ63,
CB0 - CB7
Input
Output
Level
—
Data and Check Bit Input/Output pins.
DQMB0 -
DQMB7
Input
Pulse
Active
High
The Data Input/Output masks, associated with one data byte, place the DQ buffers in a
high impedance state when sampled high. In Read mode, DQMB has a latency of two
clock cycles in Buffered mode or three clock cycles in Registered mode, and controls the
output buffers like an output enable. In Write mode, DQMB has a zero clock latency in
Buffered mode and a latency of one clock cycle in Registered mode. In this case, DQMB
operates as a byte mask by allowing input data to be written if it is low but blocks the
write operation if it is high.
V
DD
, V
SS
Supply
Power and ground for the module.
REGE
Input
Level
Active
High
(Register
Mode
Enable)
The Register Enable pin is used to permit the DIMM to operate in Buffered mode (inputs
re-driven asynchronously) or Registered mode (signals re-driven to SDRAMs when clock
rises, and held valid until next rising clock).
SA0 - 2
Input
Level
—
These signals are tied at the system planar to either V
SS
or V
DD
to configure the SPD
EEPROM.
SDA
Input
Output
Level
—
This is a bidirectional pin used to transfer data into or out of the SPD EEPROM. A resis-
tor must be connected from the SDA bus time to V
DD
to act as a pull up.
SCL
Input
Pulse
—
This signal is used to clock data into and out of the SPD EEPROM. A resistor may be
connected from the SCL bus time to V
DD
to act as a pull up.
WP
Input
Level
Active
High
This signal is pulled low on the DIMM to enable data to be written into the last 128 bytes
of the SPD EEPROM.
Discontinued (8/99 - last order; 12/99 - last ship)
相關PDF資料 |
PDF描述 |
|---|---|
| IBM13M32734BCE | 32M x 72 2-Bank Registered/Buffered SDRAM Module(32M x 72 2組寄存/緩沖同步動態RAM模塊) |
| IBM13M32734CCA | 32M x 72 1 Bank Registered/Buffered SDRAM Module(32M x 72 1組寄存/緩沖同步動態RAM模塊) |
| IBM13M32734CCB | 32M x 72 1-Bank Registered / Buffered SDRAM Module(32M x 72 1組寄存/緩沖同步動態RAM模塊) |
| IBM13M32734JCA | 32M x 72 Two Bank Registered/Buffered SDRAM Module(64M x 64 2組不帶緩沖同步動態RAM模塊) |
| IBM13M64734BCA | 64M x 72 1 Bank Registered/Buffered SDRAM Module(64M x 72 1組寄存/緩沖同步動態RAM模塊) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IBM14H5481 | 制造商:AVED Memory Products 功能描述: |
| IBM14H5540 | 制造商:AVED MEMORY PRODUCTS 功能描述: 制造商:AVED Memory Products 功能描述: |
| IBM17R8251 | 制造商:AVED Memory Products 功能描述: |
| IBM17R8252 | 制造商:AVED Memory Products 功能描述: |
| IBM1805T | 制造商:Schneider Electric 功能描述:IBM1805T |
發布緊急采購，3分鐘左右您將得到回復。