- 您現在的位置：買賣IC網 > PDF目錄379204 > IBM13M64734CCA (IBM Microeletronics) 64M x 72 2-Bank Registered/Buffered SDRAM Module(64M x 72 2組寄存/緩沖同步動態RAM模塊) PDF資料下載
參數資料
| 型號： | IBM13M64734CCA |
| 廠商： | IBM Microeletronics |
| 英文描述： | 64M x 72 2-Bank Registered/Buffered SDRAM Module(64M x 72 2組寄存/緩沖同步動態RAM模塊) |
| 中文描述： | 64米× 72 2，銀行注冊/緩沖內存模組（64米× 72 2組寄存/緩沖同步動態內存模塊） |
| 文件頁數： | 1/20頁 |
| 文件大小： | 867K |
| 代理商： | IBM13M64734CCA |
IBM13M64734CCA
64M x 72 2-Bank Registered/Buffered SDRAM Module
09K3884.F38744
10/99
IBM Corporation. All rights reserved.
Use is further subject to the provisions at the end of this document.
Page 1 of 20
Features
168-Pin Registered 8-Byte Dual In-Line Memory
Module
64Mx72 Synchronous DRAM DIMM
Performance:
-260
Device Latency
f
CK
Clock Frequency
t
AC
Clock Access Time
Intended for 66/100MHz and PC100 applica-
tions
Inputs and outputs are LVTTL (3.3V) compatible
Single 3.3V
±
0.3V power supply
Single Pulsed RAS interface
SDRAMs have four internal banks
Module has two physical banks
Fully synchronous to positive clock edge
Programmable operation:
- DIMM CAS Latency: 3, 4 (Registered
mode); 2, 3 (Buffered mode)
- Burst Type: Sequential or Interleave
- Burst Length: 1, 2, 4, 8, Full-Page (Full-
Page supports Sequential burst only)
- Operation: Burst Read and Write or Multiple
Burst Read with Single Write
Data Mask for Byte Read/Write control
Auto Refresh (CBR) and Self Refresh
Automatic and controlled Precharge commands
Suspend mode and Power Down mode
12/11/2 Addressing (Row/Column/Bank)
4096 refresh cycles distributed across 64ms
Card size: 5.25" x 1.70" x 0.320"
Gold contacts
DRAMs in TSOJ - 2 High Package
Serial Presence Detect with Write protect
Description
IBM13M64734CCA is a registered 168-Pin Syn-
chronous DRAM Dual In-Line Memory Module
(DIMM) organized as a 64Mx72 high-speed mem-
ory array and is configured as two 32Mx72 physical
banks. The DIMM uses 18 64Mx4 SDRAMs in 400
mil TSOJ stacked packages. The DIMM achieves
high-speed data-transfer rates of up to 100MHz by
employing a prefetch/pipeline hybrid architecture
that synchronizes the output data to a system clock.
The DIMM is intended for use in applications oper-
ating from 66MHz to 100MHz, PC100, memory bus
speeds, and/or heavily loaded bus applications. All
control and address signals are re-driven through
registers/buffers to the SDRAM devices. The DIMM
can be operated in either Registered mode (REGE
pin tied high), where the control/address input sig-
nals are latched in the register on one rising clock
edge and sent to the SDRAM devices on the follow-
ing rising clock edge (data access is delayed by one
clock), or in Buffered mode (REGE pin tied low),
where the input signals pass through the regis-
ter/buffer to the SDRAM devices on the same clock.
XTK simulation models of the DIMM are available to
determine which mode to design for.
A phase-lock loop (PLL) on the DIMM is used to re-
drive the clock signals to both the SDRAM devices
and the registers to minimize system clock loading.
(CK0 is connected to the PLL, and CK1, CK2, and
CK3 are terminated on the DIMM.) A single clock
enable (CKE0) controls all devices on the DIMM,
enabling the use of SDRAM Power Down modes;
the stacked devices share a common CKE pin.
Prior to any access operation, the device CAS
latency and burst type/length/operation type must
be programmed into the DIMM by address inputs
A0-A9 using the mode register set cycle. The DIMM
CAS latency when operated in Buffered mode is the
same as the device CAS latency as specified in the
SPD EEPROM. The DIMM CAS latency when oper-
ated in Registered mode is one clock later due to
the address and control signals being clocked to the
SDRAM devices.
The DIMM uses serial presence detects imple-
mented via a serial EEPROM using the two-pin IIC
protocol. The first 128 bytes of serial PD data are
programmed and locked by the DIMM manufac-
turer. The last 128 bytes are available to the cus-
tomer and may be write protected by providing a
high level to pin 81 on the DIMM. An on-board pull-
down resistor keeps this in the Write Enable mode.
All IBM 168-pin DIMMs provide a high-performance,
flexible 8-byte interface in a 5.25" long space-saving
footprint.
-360
2
-360 Units
3
2
100
66
100
MHz
7.2
10.2
7.2
ns
.
相關PDF資料 |
PDF描述 |
|---|---|
| IBM13M64734HCA | 64M x 72 Two-Bank Registered SDRAM Module(64M x 72 2組帶寄存同步動態RAM模塊) |
| IBM13M8734HCB | 8M x 72 1 Bank Registered SDRAM Module with PLL(8M x 72 1組帶鎖相環的寄存同步動態RAM模塊) |
| IBM13M8734HCC | 8M x 72 1 Bank Registered/Buffered SDRAM Module(8M x 72 1組寄存/緩沖同步動態RAM模塊) |
| IBM13M8734HCD | 8M x 72 1 Bank Registered/Buffered SDRAM Module(8M x 72 1組寄存/緩沖同步動態RAM模塊) |
| IBM13N16644HCB | 16M x 64 Two-Bank Unbuffered SDRAM Module(16M x 64 2組不帶緩沖同步動態RAM模塊) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IBM14H5481 | 制造商:AVED Memory Products 功能描述: |
| IBM14H5540 | 制造商:AVED MEMORY PRODUCTS 功能描述: 制造商:AVED Memory Products 功能描述: |
| IBM17R8251 | 制造商:AVED Memory Products 功能描述: |
| IBM17R8252 | 制造商:AVED Memory Products 功能描述: |
| IBM1805T | 制造商:Schneider Electric 功能描述:IBM1805T |
發布緊急采購，3分鐘左右您將得到回復。