- 您現在的位置：買賣IC網 > PDF目錄379206 > IBM42P10SNYAA10 (IBM Microeletronics) Gigabit Ethernet/Fibre Channel Small Form Factor Hot-Pluggable Transceiver(吉（10^ 9 G)位以太網/光纖通道熱插收發器) PDF資料下載
參數資料
| 型號： | IBM42P10SNYAA10 |
| 廠商： | IBM Microeletronics |
| 英文描述： | Gigabit Ethernet/Fibre Channel Small Form Factor Hot-Pluggable Transceiver(吉（10^ 9 G)位以太網/光纖通道熱插收發器) |
| 中文描述： | 千兆以太網/光纖通道纖巧熱插拔收發器（吉（10 ^ 9政）位以太網/光纖通道熱插收發器） |
| 文件頁數： | 8/34頁 |
| 文件大?。?/td> | 181K |
| 代理商： | IBM42P10SNYAA10 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
IBM42P10SNYAA10 IBM42P12SNYAA10
IBM42P10LNYAA10 IBM42P12LNYAA10
Gigabit Ethernet/Fibre Channel Small Form Factor Hot-Pluggable Transceiver
Page 8 of 33
08/15/00
Serial Module Definition Protocol (Serial ID)
Product specific information is stored in a Serial ID EEPROM. To read the serial data from the Serial ID mod-
ule, the following must occur (refer to Serial ID Figures 1, 2, and 3 throughout these steps):
1. Send a start sequence to the module.
This is done by changing the data line from high to low while the clock is high.
2. Send the set data address sequence.
The set data address sequence is 10100000. This sequence will allow the user to set the memory
address to start reading from.
Note: Be sure to toggle the data line only when the clock is low. Toggling the data line while the clock is
high indicates a start or stop condition.
3. Receive an acknowledge signal.
One zero bit is the acknowledge signal.
4. Send the address of the first byte to read.
The most significant bit of the address byte is the first bit and is ignored.
5. Receive an acknowledge signal.
6. Send a start command.
7. Send the read data sequence.
The read data sequence is 10100001. This sequence will allow the user to begin reading the data.
8. Receive an acknowledge signal.
9. Read a data word.
10. Send an acknowledge signal to receive the next data word or send a stop command to stop receiving
data.
A stop command is given by toggling the data from low to high while the clock is high.
The critical timings for communicating to the Serial ID EEPROM are shown in Serial ID Figure 4 on page 9.
For more information on the Serial ID protocol, see Serial ID Timing Specifications on page 20.
Serial ID Figure 1
Start and Stop Timing
SDA
SCL
START
STOP
相關PDF資料 |
PDF描述 |
|---|---|
| IBM42P10LNYAA10 | Gigabit Ethernet/Fibre Channel Small Form Factor Hot-Pluggable Transceiver(吉（10^ 9 G)位以太網/光纖通道熱插收發器) |
| IBM42P12LNYAA10 | Gigabit Ethernet/Fibre Channel Small Form Factor Hot-Pluggable Transceiver(吉（10^ 9 G)位以太網/光纖通道熱插收發器) |
| IBM42P12SNYAA10 | Gigabit Ethernet/Fibre Channel Small Form Factor Hot-Pluggable Transceiver(吉（10^ 9 G)位以太網/光纖通道熱插收發器) |
| IBM42P21SNYAA10 | 2x Fibre Channel Small Form Factor Hot-Pluggable Transceiver(2x光纖通道小外形封裝可帶電插收發器) |
| IBM42P21LNYAA10 | 1x Fibre Channel Small Form Factor Hot-Pluggable Transceiver(1x吉位光纖通道小格式可帶電插收發器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IBM42S10SNNAA20 | 制造商:IBM 功能描述:IC,DATACOM,ETHERNET TRANSCEIVER,XFO |
| IBM4MB01 | 制造商:AVED MEMORY PRODUCTS 功能描述: 制造商:AVED Memory Products 功能描述: |
| IBM63H2431-BRD | 制造商:AVED MEMORY PRODUCTS 功能描述: |
| IBM63H2469 | 制造商:AVED Memory Products 功能描述: |
| IBM64793 | 制造商:Harris Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。