- 您現在的位置：買賣IC網 > PDF目錄379206 > IBMN312804CT3 (IBM Microeletronics) 128Mb(4Mbit x 8 I/O x 4 Bank) Synchronous DRAM(128M位(4M位 x 8 I/O x 4 組)同步動態RAM) PDF資料下載
參數資料
| 型號： | IBMN312804CT3 |
| 廠商： | IBM Microeletronics |
| 英文描述： | 128Mb(4Mbit x 8 I/O x 4 Bank) Synchronous DRAM(128M位(4M位 x 8 I/O x 4 組)同步動態RAM) |
| 中文描述： | 128Mb的（的4Mb × 8的I / O × 4行）同步DRAM（128兆位（4分位× 8的I / O × 4組）同步動態RAM）的 |
| 文件頁數： | 21/66頁 |
| 文件大?。?/td> | 1696K |
| 代理商： | IBMN312804CT3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
IBMN312164CT3
IBMN312804CT3
IBMN312404CT3
Preliminary
128Mb Synchronous DRAM - Die Revision B
06K7582.H03335A
10/00
IBM Corporation. All rights reserved.
Use is further subject to the provisions at the end of this document.
Page 21 of 66
Precharge Command
The Precharge Command is used to precharge or close a bank that has been activated. The Precharge Com-
mand is triggered when CS, RAS, and WE are low and CAS is high at the rising edge of the clock. The Pre-
charge Command can be used to precharge each bank separately or all banks simultaneously. Three
address bits, A10, BS0, and BS1, are used to define which bank(s) is to be precharged when the command is
issued.
For read cycles, the Precharge Command may be applied (CAS latency - 1) prior to the last data output. For
write cycles, a delay must be satisfied from the start of the last burst write cycle until the Precharge Command
can be issued. This delay is known as t
DPL
, Data-in to Precharge delay.
After the Precharge Command is issued, the precharged bank must be reactivated before a new read or write
access can be executed. The delay between the Precharge Command and the Activate Command must be
greater than or equal to the Precharge time (t
RP
).
Burst Write with Auto-Precharge Interrupted by Read
Bank Selection for Precharge by Address Bits
A10
Bank Select
Precharged Bank(s)
LOW
BS0, BS1
Single bank defined by BS0, BS1
HIGH
DON’T CARE
All Banks
DIN A
0
COMMAND
NOP
NOP
NOP
Auto-Precharge
DIN A
1
CK
T0
T2
T1
T3
T4
T5
T6
T7
T8
NOP
NOP
*
NOP
t
CK3
,
DQs
CAS latency = 3
Bank A can be reactivated at completion of t
.
t
DAL
is a function of clock cycle time and speed sort.
*
READ B
DIN A
2
NOP
DOUT B
0
DOUT B
1
DOUT B
2
t
DAL
(Burst Length = 4, CAS Latency = 3)
See the Clock Frequency and Latency table.
相關PDF資料 |
PDF描述 |
|---|---|
| IBMN312164CT3 | 128Mb(8Mbit x 4 I/O x 4 Bank) Synchronous DRAM(128M位(8M位 x 4 I/O x 4 組)同步動態RAM) |
| IBMN325404CT3 | 256Mb（4Mbit x 16 I/O x 4 Bank） Synchronous DRAM(256M位（4M位 x 16 I/O x 4 組）同步動態RAM) |
| IBMN325804CT3 | 256Mb（8Mbit x 8 I/O x 4 Bank） Synchronous DRAM(256M位（8M位 x 8 I/O x 4 組）同步動態RAM) |
| IBMN325164CT3 | 256Mb（16Mbit x 4 I/O x 4 Bank） Synchronous DRAM(256M位（16M位 x 4 I/O x 4 組）同步動態RAM) |
| IBMN612404GT3B | 128Mb Double Data Rate Synchronous DRAM(128M位高速CMOS同步動態RAM（采用雙數據速率結構）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IBMN364164CT3C360 | 制造商:IBM 功能描述:* |
| IBMPPC403GAJC33C1 | 制造商:IBM 功能描述: |
| IBMPPC750CLGEQ4023 | 制造商:IBM 功能描述:MPU 750CL RISC 32BIT 90NM 400MHZ 1.15V/1.8V 278FCBGA - Trays |
| IBMPPC750CLGEQ5023 | 制造商:IBM Microelectronics 功能描述:MPU 750CL RISC 32BIT 90NM 500MHZ 1.15V/1.8V 278FCBGA - Trays |
| IBMPPC750CLGEQA033 | 制造商:IBM 功能描述:MPU 750CL RISC 32BIT 90NM 1GHZ 1.15V/1.8V 278FCBGA - Trays 制造商:IBM 功能描述:IBMIBMPPC750CLGEQA033 CPU PPC 750CL 1GHZ |
發布緊急采購，3分鐘左右您將得到回復。