- 您現在的位置：買賣IC網 > PDF目錄379206 > IBMN612804GT3B (IBM Microeletronics) 128Mb Double Data Rate Synchronous DRAM(128M位高速CMOS同步動態RAM（采用雙數據速率結構）) PDF資料下載
參數資料
| 型號： | IBMN612804GT3B |
| 廠商： | IBM Microeletronics |
| 英文描述： | 128Mb Double Data Rate Synchronous DRAM(128M位高速CMOS同步動態RAM（采用雙數據速率結構）) |
| 中文描述： | 128Mb的雙數據速率同步DRAM（128兆位高速的CMOS同步動態隨機存儲器（采用雙數據速率結構）） |
| 文件頁數： | 47/79頁 |
| 文件大?。?/td> | 1324K |
| 代理商： | IBMN612804GT3B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁
IBMN612404GT3B
IBMN612804GT3B
Preliminary
128Mb Double Data Rate Synchronous DRAM
06K0566.F39350B
1/01
IBM Corporation. All rights reserved.
Use is further subject to the provisions at the end of this document.
Page 47 of 79
Truth Table 3: Current State Bank n - Command to Bank n (Same Bank)
Current State
CS
RAS
CAS
WE
Command
Action
Notes
Any
H
X
X
X
Deselect
NOP. Continue previous operation
1-6
L
H
H
H
No Operation
NOP. Continue previous operation
1-6
Idle
L
L
H
H
Active
Select and activate row
1-6
L
L
L
H
Auto Refresh
1-7
L
L
L
L
Mode Register Set
1-7
Row Active
L
H
L
H
Read
Select column and start Read burst
1-6, 10
L
H
L
L
Write
Select column and start Write burst
1-6, 10
L
L
H
L
Precharge
Deactivate row in bank(s)
1-6, 8
Read
(Auto Precharge
Disabled)
L
H
L
H
Read
Select column and start new Read burst
1-6, 10
L
L
H
L
Precharge
Truncate Read burst, start Precharge
1-6, 8
L
H
H
L
Burst Terminate
Burst Terminate
1-6, 9
Write
(Auto Precharge
Disabled)
L
H
L
H
Read
Select column and start Read burst
1-6, 10, 11
L
H
L
L
Write
Select column and start Write burst
1-6, 10
L
L
H
L
Precharge
Truncate Write burst, start Precharge
1-6, 8, 11
1. This table applies when CKE n-1 was high and CKE n is high (see Truth Table 2: Clock Enable (CKE) and after t
XSNR /
t
XSRD
has
been met (if the previous state was self refresh).
2. This table is bank-specific, except where noted, i.e., the current state is for a specific bank and the commands shown are those
allowed to be issued to that bank when in that state. Exceptions are covered in the notes below.
3. Current state definitions:
Idle:
The bank has been precharged, and t
RP
has been met.
Row Active:
A row in the bank has been activated, and t
RCD
has been met. No data bursts/accesses and no register
accesses are in progress.
Read:
A Read burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated.
Write:
A Write burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated.
4. The following states must not be interrupted by a command issued to the same bank.
Precharging:
Starts with registration of a Precharge command and ends when t
RP
is met. Once t
RP
is met, the bank is in the
idle state.
Row Activating: Starts with registration of an Active command and ends when t
RCD
is met. Once t
RCD
is met, the bank is in the
“row active” state.
Read w/Auto Precharge Enabled: Starts with registration of a Read command with Auto Precharge enabled and ends when t
RP
has been met. Once t
RP
is met, the bank is in the idle state.
Write w/Auto Precharge Enabled: Starts with registration of a Write command with Auto Precharge enabled and ends when t
RP
has been met. Once t
RP
is met, the bank is in the idle state.
Deselect or NOP commands, or allowable commands to the other bank should be issued on any clock edge occurring during these
states. Allowable commands to the other bank are determined by its current state and according to Truth Table 4.
5. The following states must not be interrupted by any executable command; Deselect or NOP commands must be applied on each
positive clock edge during these states.
Refreshing:
Starts with registration of an Auto Refresh command and ends when t
RFC
is met. Once t
RFC
is met, the DDR
SDRAM is in the “all banks idle” state.
Accessing Mode Register: Starts with registration of a Mode Register Set command and ends when t
MRD
has been met. Once
t
MRD
is met, the DDR SDRAM is in the “all banks idle” state.
Precharging All: Starts with registration of a Precharge All command and ends when t
RP
is met. Once t
RP
is met, all banks is in
the idle state.
6. All states and sequences not shown are illegal or reserved.
7. Not bank-specific; requires that all banks are idle.
8. May or may not be bank-specific; if all/any banks are to be precharged, all/any must be in a valid state for precharging.
9. Not bank-specific; Burst terminate affects the most recent Read burst, regardless of bank.
10. Reads or Writes listed in the Command/Action column include Reads or Writes with Auto Precharge enabled and Reads or Writes
with Auto Precharge disabled.
11. Requires appropriate DM masking.
相關PDF資料 |
PDF描述 |
|---|---|
| IBMN625404GT3B | 256Mb Double Data Rate Synchronous DRAM(256M位雙數據速率同步動態RAM) |
| IBMN625804GT3B | 256Mb Double Data Rate Synchronous DRAM(256M位雙數據速率同步動態RAM) |
| ICM7321 | SINGLE 12/10/8-BIT VOLTAGE-OUTPUT DACS |
| ICM7321M | SINGLE 12/10/8-BIT VOLTAGE-OUTPUT DACS |
| ICM7321MG | SINGLE 12/10/8-BIT VOLTAGE-OUTPUT DACS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IBMPPC403GAJC33C1 | 制造商:IBM 功能描述: |
| IBMPPC750CLGEQ4023 | 制造商:IBM 功能描述:MPU 750CL RISC 32BIT 90NM 400MHZ 1.15V/1.8V 278FCBGA - Trays |
| IBMPPC750CLGEQ5023 | 制造商:IBM Microelectronics 功能描述:MPU 750CL RISC 32BIT 90NM 500MHZ 1.15V/1.8V 278FCBGA - Trays |
| IBMPPC750CLGEQA033 | 制造商:IBM 功能描述:MPU 750CL RISC 32BIT 90NM 1GHZ 1.15V/1.8V 278FCBGA - Trays 制造商:IBM 功能描述:IBMIBMPPC750CLGEQA033 CPU PPC 750CL 1GHZ |
| IBN100 | 制造商:Hubbell Wiring Device-Kellems 功能描述:ICON, BLANK,BR,100PK |
發布緊急采購，3分鐘左右您將得到回復。