- 您現在的位置：買賣IC網 > PDF目錄384523 > ISL59830A (Intersil Corporation) True Single Supply Video Driver With Power Down PDF資料下載
參數資料
| 型號： | ISL59830A |
| 廠商： | Intersil Corporation |
| 英文描述： | True Single Supply Video Driver With Power Down |
| 中文描述： | 真正的單電源視頻驅動器，帶有斷電 |
| 文件頁數： | 13/15頁 |
| 文件大?。?/td> | 396K |
| 代理商： | ISL59830A |
13
FN6233.3
September 26, 2006
standard encodes sync on the Y channel and it is a negative-
going signal; easily handled by the ISL59830A without the need
of an additional supply as the ISL59830A generates a negative
rail placed at negative 1/2 the positive supply. Additionally, the
Pb and Pr are bipolar analog signals and the video signals are
negative-going; and again easily handled by the ISL59830A.
Driving Capacitive Loads and Cables
The ISL59830A, internally-compensated to drive 75
cables,
will drive 10pF loads in parallel with 1k
with less than 5dB of
peaking. If less peaking is required, a small series resistor,
usually between 5
to 50
, can be placed in series with the
output. This will reduce peaking at the expense of a slight
closed loop gain reduction. When used as a cable driver,
double termination is always recommended for reflection-free
performance. For those applications, a back-termination series
resistor at the amplifier's output will isolate the amplifier from
the cable and allow extensive capacitive drive. However, other
applications may have high capacitive loads without a back-
termination resistor. Again, a small series resistor at the output
can help to reduce peaking. The ISL59830A is a triple amplifier
designed to drive three channels; simply deal with each
channel separately as described in this section.
DC-Restore
When the ISL59830A is AC-coupled it becomes necessary
to restore the DC reference for the signal. This is
accomplished with a DC-restore system applied between the
capacitive "AC" coupling and the input of the device. Refer to
Application Circuit for reference DC-restore solution.
Disable/Power-Down
The ISL59830A can be disabled and its output placed in a
high impedance state. The turn-off time is around 25ns and
the turn-on time is around 200ns. When disabled, the
amplifier's supply current is reduced to 0.9mA typically,
thereby effectively eliminating the power consumption. The
amplifier's power-down can be controlled by standard TTL or
CMOS signal levels at the EN and PD pins. The applied
logic signal is relative to V
S
- pin. Letting the EN and PD pins
float or applying a signal that is less than 0.8V above V
S
- will
enable the amplifier. The amplifier will be disabled when the
signal at EN pin is 2V above V
S
-.
The amplifier must be
disabled (EN pin is high) whenever the charge pump is
disabled (PD pin is high). EN and PD pins should be
connected together to allow amplifier and charge pump
to enable/disable simultaneously.
Output Drive Capability
The ISL59830A does not have internal short-circuit
protection circuitry. A short-circuit current of 80mA sourcing
and 150mA sinking for the output is connected to half way
between the rails with a 10
resistor. If the output is shorted
indefinitely, the power dissipation could easily increase such
that the part will be destroyed. Maximum reliability is
maintained if the output current never exceeds ±40mA, after
which the electro-migration limit of the process will be
exceeded and the part will be damaged. This limit is set by
the design of the internal metal interconnections.
Power Dissipation
With the high output drive capability of the ISL59830A, it is
possible to exceed the +150°C absolute maximum junction
temperature under certain load current conditions.
Therefore, it is important to calculate the maximum junction
temperature for an application to determine if load conditions
or package types need to be modified to assure operation of
the amplifier in a safe operating area.
The maximum power dissipation allowed in a package is
determined according to:
Where:
T
JMAX
= Maximum junction temperature
T
AMAX
= Maximum ambient temperature
Θ
JA
= Thermal resistance of the package
The maximum power dissipation actually produced by an IC
is the total quiescent supply current times the total power
supply voltage, plus the power in the IC due to the load, or:
for sourcing:
for sinking:
Where:
V
S
= Supply voltage
I
SMAX
= Maximum quiescent supply current
V
OUT
= Maximum output voltage of the application
R
LOAD
= Load resistance tied to ground
I
LOAD
= Load current
i = Number of output channels
By setting the two P
DMAX
equations equal to each other, we
can solve the output current and R
LOAD
to avoid the device
overheat.
PD
MAX
T
--------------------------------------------
T
JA
–
=
PD
MAX
V
S
I
SMAX
V
S
V
OUT
i
–
(
)
+
×
V
i
L
-----------------
×
=
PD
MAX
V
S
I
SMAX
V
OUT
i
V
S
–
(
)
+
×
I
LOAD
i
×
=
ISL59830A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL59830AIAZ | True Single Supply Video Driver With Power Down |
| ISL59830IA-T7 | True Single Supply Video Driver |
| ISL59830IAZ-T7 | True Single Supply Video Driver |
| ISL59885ISZR5260 | Auto-Adjusting Sync Separator for HD and SD Video |
| ISL59885ISZ-T7R5260 | Auto-Adjusting Sync Separator for HD and SD Video |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL59830AIAZ | 功能描述:IC VIDEO DRIVER TRUE SGL 16-QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| ISL59830AIAZ-T7 | 功能描述:IC VIDEO DRIVER TRUE SGL 16-QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| ISL59830IA | 功能描述:IC DRIVER VIDEO SGL 3.3V 16-QSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| ISL59830IA-EVAL | 制造商:Intersil Corporation 功能描述:TRUE SGL SUPPLY VID DRVR - Bulk |
| ISL59830IA-T13 | 功能描述:IC VID DRIVER TRUE SGL 16-QSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。