- 您現在的位置：買賣IC網 > PDF目錄384524 > ISL6298-2CR3 (Intersil Corporation) Li-ion/Li-Polymer Battery Charger PDF資料下載
參數資料
| 型號： | ISL6298-2CR3 |
| 廠商： | Intersil Corporation |
| 英文描述： | Li-ion/Li-Polymer Battery Charger |
| 中文描述： | 鋰聚合物電池充電器 |
| 文件頁數： | 10/17頁 |
| 文件大?。?/td> | 445K |
| 代理商： | ISL6298-2CR3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
10
FN9173.3
July 20, 2005
Theory of Operation
The ISL6298 is an integrated charger optimized for low-
capacity single-cell Li-ion or Li-polymer batteries. It charges
a battery with the constant current (CC) and constant voltage
(CV) profile. The charge current is trimmed to have better
than 10% accuracy at 250mA and is programmable up to
450mA. The charge voltage has 1% accuracy.
Figure 20 shows the typical operating waveforms after
power on. The power is applied at t
0
. When the input voltage
reaches the power-on reset (POR) threshold at t
1
, the V2P8
pin starts to output a 2.8V supply. This supply also powers
the internal control circuit. The POR initiates a charge cycle.
Six different ways can initiate a charge cycle, as listed in
Table 1.
A charge cycle goes through a trickle mode (t
1
to t
2
), a
constant current (CC) mode (t
2
to t
3
) and a constant voltage
(CV) mode (t
3
to t
5
). The total fast charge (CC and CV) time
(t
2
to t
5
) is programmed by users to prevent charging a faulty
battery for an excessively long time. At the end of the fast
charge time (t
5
), the charger is terminated. The charger
must reach an end-of-charge (EOC) condition before the
termination; otherwise, the charger issues a fault indication
through the FAULT pin. The charger issues a logic low signal
at the STATUS pin at the beginning of a charge cycle. When
the EOC condition is reached, the STATUS rises to high, as
shown at t
4
.
After termination, if the battery voltage drops below a
recharge threshold (t
6
in Figure 20), a re-charge cycle will
take place. The total time for the recharge cycle is the total
fast charge time (t
7
to t
8
). The trickle charge time is
negligible in a recharge cycle. More detailed description for
the operation is given below.
Power on Reset (POR)
The ISL6298 resets itself as the input voltage rises above
the POR rising threshold. The V2P8 pin outputs a 2.8V
voltage, the internal oscillator starts to oscillate, the internal
timer is reset, and the charger begins to charge the battery.
The two indication pins, STATUS and FAULT, indicate a
LOW and a HIGH logic signal respectively. Figure 20
illustrates the startup of the charger between t
0
to t
2
.
The ISL6298 has a typical rising POR threshold of 3.4V and
a falling POR threshold of 2.4V. The 2.4V falling threshold
guarantees charger operation with a current-limited adapter
to minimize the thermal dissipation. See more details on
using a current-limited adapter in the ISL6292 datasheet,
available at http://www.intersil.com.
Internal Oscillator
The internal oscillator (see the Block Diagram) establishes a
timing reference. The oscillation period is programmable
with an external timing capacitor, C
TIME
, as shown in Typical
Applications. The oscillator charges the timing capacitor to
1.5V and then discharges it to 0.5V in one period, both with
10
μ
A current. The period T
OSC
is:
(EQ. 1)
A 1nF capacitor results in a 0.2ms oscillation period.
Total Fast Charge Time
The total fast charge time TIMEOUT is also programmed by
the C
TIME
. A 22-stage binary counter increments each
oscillation period to set the TIMEOUT, thus,
(EQ. 2)
A 1nF capacitor leads to 14 minutes of TIMEOUT. If a user
needs to set the TIMEOUT to 3.5 hours, a 15nF capacitor is
required. The charger must reach EOC before the charger
terminates, otherwise, a TIMEOUT fault will be issued.
Trickle Charge Time
The trickle charge time is limited to 1/8 of TIMEOUT. If the
trickle charge time (t
1
to t
2
) exceeds the limit, a TIMEOUT
fault will be issued. The end of trickle charger is determined
by the battery voltage staying above the trickle charge
threshold (given in the Electrical Specification) for 15
consecutive cycles of T
OSC
; therefore, the minimum time
TABLE 1. EVENTS THAT LEADS TO A NEW CHARGE CYCLE
#
EVENT
1
Power on Reset
2
The VIN pin voltage drops below the VBAT pin voltage and
then rises back above the VBAT pin voltage
3
A new battery being inserted (detected by TEMP pin)
4
The battery voltage drops below a recharge threshold after
completing a charge cycle
5
recovery from a battery over-temperature fault
6
the EN pin is toggled from GND to floating
FIGURE 20. TYPICAL OPERATING WAVEFORMS
VIN
V2P8
STATUS
FAULT
VBAT
I
CHARGE
15 Cycles to
1/8 TIMEOUT
15 Cycles
POR Threshold
2.8V V
MIN
V
RECHRG
t
0
t
1
t
2
t
3
t
4
t
5
t
6
t
7
t
8
Charge Cycle
Charge Cycle
I
MIN
T
OSC
0.2 10
6
C
TIME
=
onds
sec
(
)
TIMEOUT
2
22
T
OSC
14
C
-----------------
=
=
minutes
(
)
ISL6298
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6298-2CR3Z | Quadruple 2-Input Exclusive-OR Gates 14-SOIC -40 to 85 |
| ISL6298-2CR4Z | Li-ion/Li-Polymer Battery Charger |
| ISL6298CR4Z | Quadruple 2-Input Exclusive-OR Gates 14-SSOP -40 to 85 |
| ISL6298-2CR4Z-T | Li-ion/Li-Polymer Battery Charger |
| ISL6298CR4Z-T | Li-ion/Li-Polymer Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6298-2CR3Z | 功能描述:IC CHARGER LI-ION 4.2V 3X3 10DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6298-2CR3Z-T | 功能描述:IC CHARGER LI-ION POLYMER 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6298-2CR4Z | 功能描述:IC CHARGER LI-ION 4.2V 4X4 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| ISL6298-2CR4Z-T | 功能描述:IC CHARGER LI-ION POLYMER 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6298CR4Z | 制造商:Intersil Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。