- 您現在的位置：買賣IC網 > PDF目錄374254 > K3NC-NB2C (Omron Electronics LLC) Up/Down Counting Meter PDF資料下載
參數資料
| 型號： | K3NC-NB2C |
| 廠商： | Omron Electronics LLC |
| 英文描述： | Up/Down Counting Meter |
| 中文描述： | 上/下計數儀 |
| 文件頁數： | 12/23頁 |
| 文件大?。?/td> | 669K |
| 代理商： | K3NC-NB2C |
C-142
Up/Down Counting Meter
K3NC
I
Output Operation Timing in RUN Mode (Relay and Transistor Outputs)
The K3NC can output the results of Up/Down counting as comparative outputs.
The output mode can be set to the ALL-H mode or the ALL-L mode.
While the reset signal is ON, the counting value will return to zero.
When the compensation signal is ON, the K3NC will be in counting operation starting with the preset compensation value. Depending on the setting
conditions, the compensation value will be effective only for the incrementing operation.
I
Output Delay (Reference Value)
The following table shows the time required for a K3NC in a system to go into reverse output operation after the counting value reaches the value
preset with the K3NC, and is due to the output processing time of the K3NC, signal transmission time of the system, and the relay connected to
the K3NC.
Note:
Output delay time varies with the operating environment. If the output delay time will possibly have a serious influence on your system, check
the actual output delay time before applying the K3NC to the system.
I
Input Mode and Counting Values
Note: 1.
“
B
”
must be larger than half the minimum signal width. If it is smaller, an error of
±
1 count may occur.
2.
Refer to the following for the meanings of the H and L characters in the above timing charts.
ALL-H
If the ALL-H output mode is selected, outputs 1 to 5 will be
ON when the measured value exceeds set values 1 to 5.
ALL-L
If the ALL-L output mode is selected, outputs 1 to 5 will be
ON when the measured value is less than set values 1 to 5.
Note:
Set value 2 < compensation value < set value 3
Note:
Set value 2 < compensation value < set value 3
Measured value
Set value 5
Set value 4
Set value 3
Set value 2
Set value 1
Reset
Output 5
Output 4
Output 3
Output 2
Output 1
See note
Measured value
Set value 5
Set value 4
Set value 3
Set value 2
Set value 1
Reset
Output 5
Output 4
Output 3
Output 2
Output 1
See note
Compensation
value
Compensation
value
Control I/O
Output or response delay time
Relay contact output
NPN/PNP transistor output
Reset input
Compensation input
Bank switch
3.0 to 10.0 ms
0.1 to 0.6 ms
12.0 to 16.0 ms
12.0 to 16.0 ms
60.0 to 100.0 ms
u-d b
: Up/Down B individual input
u-d c
: Up/Down C phase difference input
Signal
No-voltage input
Short-circuit
Open
H
L
INA
INB
Counting
value
INA
INB
Counting
value
相關PDF資料 |
PDF描述 |
|---|---|
| K3NC-PB1A | Up/Down Counting Meter |
| K3NC-PB1C | Up/Down Counting Meter |
| K3NC-PB2A | Up/Down Counting Meter |
| K3NC-PB2C | Up/Down Counting Meter |
| K3S7V2000M-TC | 64M-Bit (4Mx16 /2Mx32) Synchronous MASKROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| K3NCPB1A | 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Up/Down Counting Meter |
| K3NC-PB1A | 制造商:OMRON 制造商全稱:Omron Electronics LLC 功能描述:Up/Down Counting Meter |
| K3NCPB1C | 功能描述:控制器 RoHS:否 制造商:Omron Industrial 模擬/數字:Digital 類型:Digital Temperature Controller 顯示器類型:11-Segment, 4 Digit 電源電壓:100 VAC to 240 VAC 安裝: 控制方法: 大小:48 mm x 48 mm |
| K3NC-PB1C | 制造商:OMRON 制造商全稱:Omron Electronics LLC 功能描述:Up/Down Counting Meter |
| K3NCPB2A | 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Up/Down Counting Meter |
發布緊急采購，3分鐘左右您將得到回復。